This study investigates the structural performance of a redesigned AAR Type E knuckle coupler using finite element analysis (FEA). The modified knuckle incorporates geometric reinforcement in critical load-bearing regions together with a hollow internal structure aimed at reducing component weight while maintaining structural integrity. Two numerical models were developed: a component level model, in which the knuckle was analyzed independently, and an assembly-level model that integrates the knuckle with the coupler body to capture realistic load transfer through contact interactions. Both models were subjected to a tensile draft load of 650,000 lbs (2670 kN) in accordance with Association of American Railroads (AAR) standards. The component-level analysis predicted peak von Mises stresses of approximately 1050 MPa, primarily concentrated near the pivot pin hole and curved pulling face regions. When contact interactions between the knuckle and coupler body were included in the assembly model, the representative peak stress decreased to approximately 950 MPa, corresponding to a stress reduction of about 10% due to load redistribution across the assembly interfaces. Highly localized stress peaks at sharp geometric edges were identified as numerical stress singularities and were excluded from engineering interpretation. The results demonstrate that assembly-level finite element modeling provides a more realistic representation of load transfer mechanisms in railway coupler systems and is essential for accurately predicting stress distribution and identifying critical fatigue-prone regions. These findings provide valuable insights for improving the structural reliability and design optimization of freight rail coupler components.
Friction-induced vibration is a critical issue in railway tread brake systems, as it can affect braking stability, wear, and the dynamic response of mechanically connected components. This study numerically investigates the self-excited vibration behavior of a tread brake unit and its interaction with a slack adjuster compensator under braking conditions. A simplified single-degree-of-freedom dynamic model incorporating a velocity-dependent Coulomb friction formulation is developed to analyze the vibration response of the brake block under continuous sliding conditions. The governing nonlinear differential equation is solved using the Runge–Kutta method, and time- and frequency-domain analyses are performed to identify dominant vibration characteristics. The numerical results indicate the presence of low-frequency self-excited vibration induced by dry friction, while the contact interface remains in a continuous sliding regime and no classical stick–slip transition involving intermittent adhesion is observed. The dominant vibration frequency is approximately 0.35 Hz, reflecting the global mass–stiffness dynamics of the brake unit rather than high-frequency stick–slip or squeal phenomena. A finite element modal analysis of the slack adjuster compensator shows that its natural frequencies are several orders of magnitude higher than the dominant vibration frequency, indicating that resonance is unlikely under the investigated operating conditions. The findings provide insight into friction-induced vibration mechanisms in railway tread brake systems and their implications for vibration safety and structural integrity.
Rising sea levels and seasonal decreases in freshwater discharge are accelerating the penetration of saline water into freshwater agricultural canals, aquaculture, and irrigation systems in low-lying coastal areas, making saltwater intrusion a growing threat. This paper reports on the design, development and field validation of a real-time, solar-powered smart buoy for continuous saltwater intrusion monitoring in agricultural canals. The proposed system comprises a multi-parameter electrical conductivity sensor, a water-level sensor based on a pressure transducer, an ESP32 microcontroller, an energy subsystem powered by photovoltaics, and a cloud-based Internet of Things (IoT) platform capable of automatically sending notifications to a smartphone when predefined salinity thresholds are exceeded. Field experiments were carried out at seven monitoring stations along the Khlong Bang Mot canal, Bangkok, Thailand to assess (1) sensor accuracy, (2) power autonomy, (3) flotation stability, (4) communication reliability and (5) spatial salinity distribution under representative operating conditions. The monitoring platform showed measurement accuracy within the specified ±2% full-scale range for the salinity levels studied, and temperature compensation was effective in minimizing conductivity drift across different environmental conditions. The photovoltaic power subsystem provided ~60 h of continuous autonomous operation per battery charge cycle, and the reinforced buoy structure allowed stable operation at canal wave heights of 5–20 cm with a maximum tilt angle of 20.7° and rapid equilibrium recovery. The field deployment successfully detected localized saltwater intrusion and provided smartphone alerts in real time within 10 s of threshold exceedance. The proposed smart buoy provides a reliable, low-cost, and field-deployable solution for ongoing surveillance of saltwater intrusion in freshwater agricultural canals. The integrated platform combines environmental sensing, autonomous energy management, wireless communication and real-time decision support to provide a practical approach to improve irrigation management, reduce salinity-related agricultural losses and enhance climate resilience in vulnerable farming communities.