Anatoli Mokhov

Dr. Anatoli Mokhov

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 June 2022 in Renewable and Sustainable Energy Reviews
Verified
Journal Article
Closed access
LFLiyuan Fan
Liyuan Fan
CLChao'en Li
Chao'en Li
LBLindert van Biert
Lindert van Biert
SZShou-Han Zhou
Shou-Han Zhou
ATAsif Nadeem Tabish
Asif Nadeem Tabish
WCWeiwei Cai
Weiwei Cai

15 July 2022 in Combustion and Flame
Verified
Journal Article
Open access
SNSeyed Bahram Nourani Najafi
Seyed Bahram Nourani Najafi
AMAnatoli Mokhov
Anatoli Mokhov
HLH.B. Levinsky
H.B. Levinsky

1 September 2021 in Journal of Power Sources
Verified
Journal Article
Closed access
LFLiyuan Fan
Liyuan Fan
AMAnatoli Mokhov
Anatoli Mokhov
SSS. Ali Saadabadi
S. Ali Saadabadi
NBNigel Brandon
Nigel Brandon
PAPurushothaman Vellayani Aravind
Purushothaman Vellayani Aravind

31 May 2008 in Combustion and Flame
Verified
Journal Article
Closed access
VVV Vanessen
V Vanessen
ASA.V. Sepman
A.V. Sepman
AMAnatoli Mokhov
Anatoli Mokhov
HLH.B. Levinsky
H.B. Levinsky

26 March 2021 in Energy & Fuels
Verified
Journal Article
Open access
SNS. B. Nourani Najafi
S. B. Nourani Najafi
JOJ. A. van Oijen
J. A. van Oijen
HLH. B. Levinsky
H. B. Levinsky
AMAnatoli Mokhov
Anatoli Mokhov
Spatial distributions of temperature, major species, and OH mole fractions under moderate or intense low-oxygen-dilution (MILD) conditions in a laminar-jet-in-hot-coflow configuration were measured using spontaneous Raman and laser-induced-fluorescence methods. A preheated mixture of 18% CH4/82% N2 at 1100 K was used as fuel, while the products of a laminar, flat, premixed burner-stabilized flame with an equivalence ratio of 0.8 at 1550 K were used as the oxidizer. For comparison, experiments replacing the fuel by pure N2 were also performed. The measurements are compared with the results of numerical simulations performed using the GRI-Mech 3.0 chemical mechanism and a multicomponent mixture-averaged transport model. Analysis of the data shows that the maximum axial and radial temperature and OH mole fraction occur on the lean side of the stoichiometric mixture fraction. MILD combustion generates maximum OH mole fractions of ∼700 ppm in the radial profiles close to the burner exit and ∼300 ppm along the centerline, more than five times lower than those measured in equivalent methane/air diffusion flames. Overall, good qualitative and quantitative agreement is found between the results of detailed computations and experiments, with the maximum differences observed in the axial OH profiles, which are just outside the estimated experimental uncertainty. Analysis of the computational results shows that differential diffusion hinders the use of the mixture fraction to estimate the equilibrium temperature and species fractions, causing an overestimation of the stoichiometric temperature by ∼200 K. Calculating the equilibrium quantities based on the local (computed) species fractions shows an axial temperature profile that differs from that experimentally/computationally determined by less than 25 K. The analysis further shows that the measured OH mole fractions are roughly three times higher than the (locally determined) equilibrium value.

22 October 2019 in Energy & Fuels
Verified
Journal Article
Open access
LDLiming Dai
Liming Dai
AMAnatoli Mokhov
Anatoli Mokhov
HLHoward Levinsky
Howard Levinsky
The flame temperatures in flat, laminar premixed dimethyl ether (DME)/air flames with varying degrees of burner stabilization were measured by spontaneous Raman scattering in a range of equivalence ratio's from 0.6 to 2.0. Three commonly used mechanisms to describe DME oxidation were evaluated by comparing the calculated variation of flame temperature derived from 1-D flame calculations as a function of DME/air exit velocity with those obtained from the measurements. The results showed the necessity of incorporating radiative heat losses in the flame calculations. The three mechanisms yield similar results at φ = 0.6 and 2.0, underpredicting the temperatures more than 30 K. Differences between measured and predicted temperatures for burner-stabilized flames are seen to indicate whether a free-flame burning velocity is too high or too low. The results suggest a free flame burning velocity of ~14 cm/s at φ = 0.6, 2 cm/s lower than the mechanisms predict, and burning velocities closer to 49 cm/s and 40 cm/s for φ = 1.0 and 1.4, respectively. Sensitivity analysis of the DME/air flame temperature as a function of exit velocity shows that the DME decomposition reaction and H abstraction from DME become important in the rich flames at φ = 1.7 and 2.0.