Daniil Andreevich Korotych

Mr. Daniil Andreevich Korotych

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 September 2023 in Advanced Engineering Research (Rostov-on-Don)
Verified
Journal Article
Open access
PDF file
DKDaniil Andreevich Korotych
Daniil Andreevich Korotych
VSV. S. Sidorenko
V. S. Sidorenko
SPS. P. Prikhodko
S. P. Prikhodko
Introduction. Long-stroke movements in automated pneumatic drives account for a significant number of executive movements in coordinate tables, automated warehouses, cutting machines, etc. Long-stroke movements degrade the dynamic quality and positioning of the drive. This is due to the friction of the piston and the nonlinear characteristics of the compressed gas flow in significant volumes of the pressure and drain cavities of the cylinder. Thus, it seems promising to create an automated position pneumatic actuator for long-stroke movements. This will increase the productivity of processes while providing the declared accuracy. The objective of the work is to obtain a mathematical model and dependences of the critical parameters of the proposed automated position long-stroke pneumatic drive of fabrication system in the areas of acceleration, steady-speed movement, deceleration, and braking.Materials and Methods. The basis for calculations and modeling was the scheme of two trajectories of movement from point A to point E, taking into account the forces expended on these processes. The optimal displacement was determined using the Portnyagin’s principle (i.e., optimal performance). Proportional drive control was presented as a method of achieving the result. For long-stroke drive movements, schematic solution and design scheme were visualized in detail (presented as drawings). An original jet sensor with an internal pneumatic connection and a pneumo-mechanic discrete-proportional device for the control loop performance were proposed. The mathematical model included the movement and braking of the piston, the balance of mass flow, the pressure at points, and the control loop. The system of equations was solved by the Runge — Kutta method in the SimInTech software product. Based on the results of the study of a generalized mathematical model, the dependences of changes in the kinematic, power and pneumatic properties of the drive were constructed in real time during a typical positioning cycle. The information was summarized and presented as a set of graphs.Results. The mathematical model was formed according to a set of calculations. It took into account the dependences characteristic of the movement of the piston of the pneumatic cylinder. The balance of mass flow was investigated by the equations of gas flow during compression in the chamber, through distributors and throttles, in the discharge and drain cavities and in the control device. Inequalities describing the pressures at the points and the control loop were considered. A complex mathematical model was solved in the SimInTech software environment by the Runge — Kutta method with a variable integration step. A fragment of the program was selected as one of the illustrations. It showed that the software used the following indicators for calculations: target and reduced coordinates; absolute gas constant; coefficients of spring stiffness, resistance, adiabatic and viscous friction in the piston; compressor pressure; mass of the moving parts of the pneumatic actuator; strength of external resistances; diameters of the pipeline, the pneumatic cylinder piston and the braking device; length of the stroke of the cylinder piston; area of piston cavities and throttles; length of the pipeline and its internal volume. Thus, the program manipulated a significant set of data, which made it possible to obtain meaningful and adequate results. The relationship of blocks and diagrams used in solving the model was schematically shown. We are talking about graphs of movements, areas, pressures, velocities and temperatures. Blocks with the program text and intended for integration were used. Thus, a mathematical model of an automated pneumatic drive of the fabrication system and the dependences of the basic parameters of its operation were obtained. The graphs indicated that the operating mechanism of the pneumatic actuator properly followed the proposed trajectory.Discussion and Conclusion. The research results allowed us to consider several stages of long-stroke movement of the drive, to determine the time frame of these processes (from 0 to 0.65s), as well as changes in pressure and speed of movement of the pneumatic cylinder carriage recorded in these intervals. There were five such stages: acceleration, steady-speed movement, deceleration, movement with positioning speed, and braking. Further research will focus on optimizing the system to reduce the duration and maintain accurate positioning under external influences.

21 September 2022
Verified
Conference Paper
Closed access
DKDaniil Andreevich Korotych
Daniil Andreevich Korotych
VSValentin Sidorenko
Valentin Sidorenko
SPSergey Prikhodko
Sergey Prikhodko
- Long-stroke installation and coordinate movements occupy a significant amount of executive movements, these movements are used in coordinate tables, automated warehouses, cutting machines, etc. Long-stroke movements entail a deterioration in the dynamic quality and positioning of the drive due to the presence of piston friction and nonlinear characteristics of the compressed gas flow in significant volumes of the pressure and drain cavities of the cylinder. In this paper, a positional pneumatic drive system for long-stroke installation movement is proposed, a mathematical model is compiled, oscillograms are obtained, a description and discussion are carried out.

19 March 2026 in Actuators
Verified
Journal Article
Open access
PDF file
DKDaniil Andreevich Korotych
Daniil Andreevich Korotych
VGVyacheslav Grishchenko Grishchenko
Vyacheslav Grishchenko Grishchenko
Alexey BeskopylnyAlexey Beskopylny
Alexey Beskopylny
This paper presents an original positional pneumatic actuator for long-stroke coordinate mechanisms. The design integrates a rodless pneumatic cylinder, a jet control system, and an external braking device. It achieves a positioning accuracy of 200 microns, a discrete step of 2 mm, and an average speed of 0.15 m/s over a maximum stroke of 6 m. This solution offers a two-fold improvement in technical, economic, and operational performance compared to electromechanical drives. A mathematical model of the drive was developed using SimInTech software and validated with a custom-built experimental stand. The discrepancy between calculated and experimental data does not exceed 18%. The study established the dependence of positioning accuracy on the load and kinematic characteristics of the drive, which helps reduce design time for coordinate mechanisms. As a result of the research, a new scheme of a positional pneumatic actuator has been developed and experimentally confirmed, which allows for a two-fold improvement in technical and economic indicators compared to electromechanical analogs due to the original combination of a rodless cylinder, a jet control system, and an external braking device.

29 September 2025 in Advanced Engineering Research (Rostov-on-Don)
Verified
Journal Article
Open access
PDF file
DKDaniil Andreevich Korotych
Daniil Andreevich Korotych
Introduction. In modern industrial processes, pneumatic actuators with long-stroke movements play an important role. However, their use is limited by low accuracy resulting from the difficulties of controlling air flows. These limitations are caused by the compressibility of air and thermodynamic processes, which makes it urgent to improve the accuracy of such systems. The conducted analysis of scientific literature shows that modern research is mainly focused on the use of systems with standard cylinders with a working stroke limited to three meters. At the same time, the issues of development and research of long-stroke systems of rodless pneumatic drives, capable of having a stroke length of up to six meters, remain insufficiently studied. The introduction of advanced control systems in this type of drives involves significant investments in a high-tech electronic base and additional structural elements. In this regard, the development of fundamentally new technical solutions that allow for the efficient operation of mechanisms with a working stroke of more than three meters while maintaining the required technical parameters and economic efficiency, is of particular relevance. In the framework of previous studies, the author proposed a design of a pneumatic drive for long-stroke movements, equipped with a unique control system based on a jet sensor and an external brake mechanism. Its mathematical modeling and theoretical analysis were also performed, which made it possible to identify key factors affecting the accuracy of positioning. To validate the mathematical model and the hypotheses put forward, the objective of this research is to experimentally verify the results of mathematical modeling of a positioning long-stroke rodless pneumatic actuator, as well as to confirm the degree of influence of key factors on positioning accuracy.Materials and Methods. The work involved a stand that was a technical model of a pneumatic drive with an original control system, including a jet sensor and an external brake device. To verify the operability and accuracy of the jet sensor readings, the spillage method was applied using the Camozzi MF4008-10-R-BV-A flow sensor after the element under study, and Camozzi SWCN-P10-P3-2 pressure sensors placed before and after the considered element. The tests conducted on the developed jet sensor showed high reliability and stability of operation in various operating modes. The experimental study of a long-stroke rodless pneumatic actuator included evaluation of the actuator's technical capabilities, analysis of positional cycles, study on the effect of external factors, and comparison of the results of computational and full-scale experiments. The results of computational and full-scale experiments were processed using the Mathcad and MATLAB software packages. The dependences of positioning accuracy on mass and stroke length were constructed.Results. The reliability of the model was established at the level of the maximum discrepancy between the experimental data and the results of mathematical modeling, which amounted to 18%. That confirmed the adequacy of the developed model for engineering calculations. The effect of the load mass on the accuracy of positioning was experimentally established. With an increase in mass from 10 to 30 kg, the accuracy decreased by 1.47 times, and with a mass of 60 kg, the accuracy deteriorated by another 1.37 times relative to the base mass of 10 kg. In addition, the effect of stop coordinates was studied: the dependence of positioning accuracy on the position of the actuator was established. When moving from 0.1 m to 0.22 m, the accuracy deteriorated by 3.2 times, but with further movement to 0.35 m, it improved by 2.2 times.Discussion. The conducted experimental studies allowed achieving good results in the development of long-stroke pneumatic drives. Successful verification of the mathematical model confirmed the correctness of both the model itself and the theoretical studies conducted in the author's previous works. The positioning accuracy of the drive of 77 microns at a distance of over three meters was reached. This indicator significantly exceeds the results presented in the studies of other authors, which shows the high potential of the developed design. The economic efficiency of the proposed solution is due to the absence of an electronic component base in the control system. This not only reduces initial production costs, but also significantly simplifies maintenance of the drive under operation. The comparative analysis with existing developments confirms the superiority of the proposed system in terms of cost criteria.Conclusion. The conducted studies confirmed the efficiency of the developed solutions for a long-stroke rodless pneumatic actuator. Practical significance of the study is determined by the possibility of using the obtained results in creating high-precision long-stroke mechanisms in various industries. The developed design can be used in automated production lines, robotic complexes, and other areas where precise positioning over significant distances is required. Promising areas for further research are the optimization of the control system parameters to reach even higher positioning accuracy, and the development of calculation methods for positioning long-stroke pneumatic drives.

21 September 2022
Verified
Conference Paper
Closed access
SPSergey Prikhodko
Sergey Prikhodko
VSValentin Sidorenko
Valentin Sidorenko
DKDaniil Andreevich Korotych
Daniil Andreevich Korotych
GDGrigory Dolgov
Grigory Dolgov
- In recent years, the use of pneumomechanical drives in a zone without technological loads is a priority, this is due to the fact that the pneumatic drive has a number of advantages, such as high speed of movement of the output link, environmental friendliness, cost, but also has a significant disadvantage, such as compressibility of the working fluid, affecting the nature of rotational movements, which is compensated by the rigidity properties of the mechanical the drive. The aim of the study is to reduce the duration for a given accuracy of the setting coordinate movements of machine mechanisms by creating a combined pneumomechanical drive with improved energy and dynamic characteristics.

10 July 2024 in VESTNIK of Samara University. Aerospace and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
SPS. P. Prikhodko
S. P. Prikhodko
VSV. S. Sidorenko
V. S. Sidorenko
DKDaniil Andreevich Korotych
Daniil Andreevich Korotych
The creation of new and improvement of existing machines and mechanisms requires the development of drive engineering and the creation of new drive systems capable of competing with currently known circuit solutions. Under these conditions, the creation of combined pneumatic-mechanical drives is an important scientific and technical task. The purpose of this work is to increase the speed at a given accuracy of auxiliary movements of the target mechanisms of technological machines by creating a pneumatic-mechanical drive with improved energy and dynamic characteristics. The technical solution of a positioning pneumatic-mechanical drive of executive movements of technological equipment is presented, mathematical and computer models are developed. In this case, the method of solving the differential equation in the SimInTech program is used. As a result, an oscillogram of transients is obtained. The developed models allow for dynamic analysis of pneumatic-mechanical systems.