The flatness of bearing pads directly affects structural load transfer safety. However, conventional total station-based inspection methods suffer from limited spatial sampling, low inspection efficiency, and high safety risks associated with working at height. To address these limitations, this paper proposes UAV-FIBP (Unmanned Aerial Vehicle-based Flatness Inspection for Bridge Pads), an automated and intelligent method for pad flatness assessment utilizing UAV-based 3D reconstruction. By designing a close-range, multi-orbit circumnavigational UAV flight path and acquiring high-overlap imagery (85% forward and 80% side overlap), a millimeter-accurate 3D model is generated via photogrammetry, achieving a high-density point cloud of ≥200 points/cm2 on the pad surface. Following point cloud denoising and region-of-interest segmentation using the Random Sample Consensus (RANSAC) algorithm, Principal Component Analysis (PCA) is employed to fit a reference plane. A dual-parameter evaluation framework is subsequently introduced: the root mean square (RMS) deviation quantifies local surface roughness, while the maximum elevation difference is derived from the angle between the normal vectors of the fitted plane and the horizontal plane, thereby enabling a comprehensive assessment of global inclination. Validation experiments conducted on laboratory-scale setups and real construction sites (involving four bridge pads) demonstrate that the proposed method achieves deviations ≤ 2 mm compared to total station measurements, satisfying the requirements stipulated in the Standards for Quality Inspection and Verification of Highways (JTG F80/1-2017). Results indicate that UAV-FIBP enables non-contact, full-coverage, and automated flatness inspection, significantly improving inspection efficiency and construction safety. This work establishes a scalable technical pathway for intelligent bridge construction.
This paper presents an integrated framework for automated detection of surface defects in infrastructures using unmanned aerial vehicles (UAVs), comprising 3D model-based adaptive path planning, high-resolution image acquisition, and an attention-enhanced instance segmentation model. However, existing approaches face two key limitations: (i) conventional UAV path planning lacks adaptive trajectory correction for non-horizontal bridge geometries, and (ii) instance segmentation models for infrastructure defects have not been systematically optimized for both accuracy and edge-device deployability. To address these gaps, the proposed framework was trained on 3625 annotated images covering two defect categories (spalling and cracking) and preliminarily validated through a proof-of-concept field study on a concrete viaduct section where seven spalling and one reinforcement exposure were detected. The methodology consists of three core components: (i) 3D model-based adaptive path planning, (ii) high-resolution image acquisition under variable infrastructure geometries, and (iii) an improved instance segmentation model based on YOLOv8-seg. To ensure consistent imaging geometry, a segmented linear interpolation method is introduced to adaptively correct flight trajectories for non-horizontal infrastructure sections. For damage detection, we propose a structurally enhanced YOLOv8-seg model, denoted as YOLOv8-seg-ECAC2f-all, which integrates Efficient Channel Attention (ECA) modules into a fully modified backbone architecture. Compared to the baseline YOLOv8-seg, the proposed model achieves a mean average precision (mAP50–95) of 91.8% for bounding box detection and 61.7% for instance segmentation, corresponding to improvements of 7.7% and 2.8%, respectively. The framework was preliminarily validated on a concrete viaduct of the Guangfojiangzhu Expressway, achieving 100% inspection coverage and detection of all eight ground-truth surface defects (seven spalling and one reinforcement exposure) in this pilot study, including two minor spalling cases (≤0.5 m2) missed by manual inspection. These results demonstrate the technical feasibility of the proposed framework for real-world concrete bridge inspection and its potential for reducing manual inspection effort while improving detection sensitivity for minor defects ().
Ground-penetrating radar (GPR) is a rapid and non-destructive technique for road sub-surface distress (RSD) detection. However, reliable interpretation of GPR images remains challenging because subsurface anomalies often present weak boundaries, ambiguous textures, and high similarity to non-distress targets. This study proposes a cross-verification intelligent algorithm that exploits complementary information from different views of 3D GPR data. Three YOLO-based detectors are trained on view-specific GPR images to identify RSD-related targets, including voids, loose structures, and manholes. By sequentially verifying detection results across different views, the proposed method improves recognition reliability under vague subsurface imaging conditions. The models are trained and evaluated on an expert-annotated field 3D GPR dataset containing 2134 location-level multi-view samples. At the selected operational thresholds, the complete cross-verification procedure achieved 95.9% precision and 98.6% recall for RSD detection in the testing subset. In a field evaluation on 15 roads, all 69 RSD locations in the expert-identified reference set were matched by automatic indications. When integrated into an automatic detection system, the method reduced manual inspection workloads by approximately 90% while maintaining high field reliability. These results demonstrate the potential of multi-view cross-verification for post-survey RSD screening and expert-assisted review.