Shota Yabui

Prof. Shota Yabui

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 November 2019 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
TATakenori Atsumi
Takenori Atsumi
SYShota Yabui
Shota Yabui
In this paper, we present a magnetic-head positioning system in hard disk drives (HDDs) with a quadruple-stage actuator system. The quadruple-stage actuator system consists of a voice coil motor, a milli actuator with two piezoelectric (PZT) elements, a micro actuator with two PZT elements, and a thermal actuator. The milli actuator is the first generation of a secondary actuator for a dual-stage actuator in the HDDs and moves a sway mode of a suspension in a head-stack assembly. The micro actuator is the second generation of the secondary actuator for the dual-stage actuator in the HDDs and moves a yaw mode of the suspension. The thermal actuator is an actuator in a development phase for future HDDs. It consists of heaters embedded in the magnetic head and move read/write elements in a horizontal direction with thermal expansion. The achievable disturbance-rejection performance of the quadruple-stage-actuator system is higher than that of the conventional triple-stage actuator system because the proposed system can decrease a negative impact caused by the stroke limitation of the thermal actuator. As a result, the quadruple-stage-actuator system enables us to improve the positioning accuracy under the external vibrations by about 48% from that with the triple-stage-actuator system.

6 July 2012 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
SYShota Yabui
Shota Yabui
AOAtushi Okuyama
Atushi Okuyama
MKMasahito Kobayashi
Masahito Kobayashi
TATakenori Atsumi
Takenori Atsumi

1 January 2013 in Journal of Advanced Mechanical Design, Systems, and Manufacturing
Verified
Journal Article
Closed access
SYShota Yabui
Shota Yabui
AOAtsushi Okuyama
Atsushi Okuyama
TATakenori Atsumi
Takenori Atsumi
MOMasaki Odai
Masaki Odai

19 November 2021 in IEEE Transactions on Magnetics
Verified
Journal Article
Open access
SYShota Yabui
Shota Yabui
TATakenori Atsumi
Takenori Atsumi
TITsuyoshi Inoue
Tsuyoshi Inoue
Hard disk drives (HDDs) used for data servers are exposed to various vibrations. These vibrations are mainly caused by the cooling fan that controls the temperature inside the server. The vibration affects the positioning accuracy of magnetic heads that read/write digital data. This is an obstacle to obtaining high data transfer rates. To compensate for vibration, the control system for the magnetic heads must have higher frequency control bandwidth as the spectra of these vibrations have peaks up to 10 kHz. In current HDDs, the control system is a triple-stage system consisting of a voice coil motor (VCM), a milliactuator, and a microactuator. In this article, we propose a design strategy for a triple-stage control system to compensate for vibration. The design strategy addresses unstable controllers in the control system. The gain of the feedback controllers of the VCM and milliactuators is increased to expand the control bandwidth. Although these feedback loops become an unstable system due to the increase in the controller gain, the controller for the microactuator is designed to stabilize the overall feedback loop. As a result, the control system achieves high control bandwidth. The performance of the proposed control system is calculated based on the compensation of the vibration caused by the data server. The proposed design can improve positioning accuracy by approximately 48%–58% compared with the conventional controller design.

22 August 2022 in Journal of Low Frequency Noise, Vibration and Active Control
Verified
Journal Article
Open access
TYTu Yilin
Tu Yilin
TITsuyoshi Inoue
Tsuyoshi Inoue
SYShota Yabui
Shota Yabui
KKKeiichi Katayama
Keiichi Katayama
STShigeyuki Tomimatsu
Shigeyuki Tomimatsu
Rotating machines are widely used as components of various industries around the world, and its normal operation of rotating machines is important. Thus, condition monitoring and fault diagnosis of rotating machines have considerable attention in recent years. Industrial statistics illustrate that 40% of total large machine breakdowns happened due to broken bearings, while for small machines, the analogous number reaches up to 90%. This study aimed at researching fault diagnosis of journal bearings using the support vector machine (SVM) method. The experimental systems of vertical and horizontal rotating shafts were developed. There was no adding any initial artificial failure in the bearing, and a little muddy water was used, and long-term vibration data in both systems were obtained in the normal operation of the machines until bearing damages occurred in the journal bearing (3-hour tests were conducted repeatedly and total 128 datasets for vertical shaft and 24 datasets for horizontal shaft were obtained). A feature selection method is focused, and a hybrid feature selection method by combining Fisher score (FS) and a sequential forward selection (SFS) method was proposed. Its accuracy and efficiency was proved experimentally with 97.14% and 100% for vertical shaft and 100% for horizontal shaft. Furthermore, as a result of the SVM model and hybrid feature selection method, the most important feature for journal bearing of horizontal rotor system was clarified as mean value of RMS, and only this feature can give good diagnosis result. It is useful suggestion in selecting the features for the fault diagnosis of horizontal rotating machines.

5 March 2020 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
SYShota Yabui
Shota Yabui
TATakenori Atsumi
Takenori Atsumi
TITsuyoshi Inoue
Tsuyoshi Inoue
Head positioning control systems are required to improve the positioning accuracy and thus increase the recording capacity of hard disk drives (HDDs). Existing head positioning control systems employ a dual-stage actuator system comprising a voice coil motor (VCM) and a piezoactuator. The control system is a multi-input single-output system, and positioning controllers must be designed for both actuators. In this article, we propose a coupling controller design method for head positioning control systems of HDDs. The proposed method designs the controllers by considering the interaction between the VCM and the piezoactuator. It is more complex than the decoupling controller design method, which is widely used to design the controllers for the dual-stage actuator system. Nevertheless, it provides greater freedom in the controller design. The main advantage is, when the entire feedback loop is stabilized, the feedback loop for each actuator does not need to be stabilized. The design results show that the proposed design method can improve the positioning accuracy with comparison to the decoupling controller design. Moreover, the amount of the required stroke of the piezoactuator is decreased by using the coupling controller design.