Zainab Hussein Mohsein

Zainab Hussein Mohsein


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2023 in Al-Qadisiyah Journal for Engineering Sciences
Verified
Journal Article
Open access
PDF file
SAShukry H. Aghdeab
Shukry H. Aghdeab
AAAhmed Basil Abdulwahhab
Ahmed Basil Abdulwahhab
ZMZainab Hussein Mohsein
Zainab Hussein Mohsein
EDM (Electrical Discharge Machining) is a common non-traditional machining technique for manufacture geometry parts made of intricate or extremely rigid metals that are challenging to manufacture using conventional manufacturing techniques. Electrical discharge machining by utilizing electrical discharge erosion, classify the meaning of material removal (MR). This paper's main objective is to discuss the ideal EDM parameters in order to use high-speed steel as workpiece AISI M2 and with using brass & copper as electrodes. Pulse on-time are (100, 150, and 200 µs), Current (10, 24 and 42 A) and Pulse off-time (4, 12 and 25 µs) are the input parameters effect on the material removal rate (MRR) used in the experimental work. The present study's findings shown that the highest MRR with using copper & brass as electrodes with pulse on-time 200 µs, pulse off-time 12 µs and current 42 A, at (0.31284 g/min and 0.18769) respectively, and the lowest average value of the removed material was when evaluating current 10 A, Ton is 100 µs, Toff is 4 µs, at (0.05451g/min and 0.01898 g/min) respectively.

20 March 2025 in Results in Engineering
Verified
Journal Article
Open access
ZMZainab Hussein Mohsein
Zainab Hussein Mohsein
AAAhmed Basil Abdulwahhab
Ahmed Basil Abdulwahhab
AHMED Mohammed AbbasAHMED Mohammed Abbas
AHMED Mohammed Abbas

28 May 2026 in Polymers
Verified
Journal Article
Open access
PDF file
Walid mahmoud ShewakhWalid mahmoud Shewakh
Walid mahmoud Shewakh
MMMajed Moosa
Majed Moosa
ZMZainab Hussein Mohsein
Zainab Hussein Mohsein
OIOsama Irfan
Osama Irfan
Fused deposition modeling (FDM) of polylactic acid (PLA) produces parts whose weak interlayer bonding and low as-printed crystallinity limit their tensile performance. This work used a Taguchi L9 orthogonal array with five replicates per cell (n = 5; N = 45 annealed specimens plus five non-annealed controls) to study how annealing temperature (70, 80, and 90 °C) and holding time (40, 60, and 80 min) change the tensile response of a commercial PLA grade (eSUN PLA+) printed on a desktop FDM machine. Differential scanning calorimetry (DSC) and X-ray diffraction (XRD) were used in parallel to measure total crystallinity, and XRD was deconvoluted to estimate the α′/α polymorph fractions; the DSC α′→α exothermic shoulder was used as an independent cross-check. Every annealed condition exceeded the non-annealed baseline ultimate tensile stress (UTS) of 39.75 ± 1.28 MPa. The optimum, 47.00 ± 0.97 MPa at 70 °C/60 min, gave an 18.2% gain. Total crystallinity rose from 8.6% (DSC baseline) to 41.8% (DSC, 90 °C/80 min), with DSC and XRD ranking the conditions consistently. ANOVA confirmed both temperature (30.0% contribution) and time (24.2%) as significant at α = 0.05. The new contribution is a combined strength–crystallinity–polymorph map for desktop FDM-printed PLA: the best-performing specimens are dominated by the disordered α′ form, while the stiffer but weaker high-temperature specimens shift toward α. A partial least squares regression on all 50 specimens supports the polymorph-composition role beyond what total crystallinity alone explains. The practical conclusion is that moderate annealing just above the glass transition gives the best balance of crystal content, polymorph character, and geometric stability for FDM-printed PLA.

1 January 2023 in Engineering and Technology Journal
Verified
Journal Article
Open access
PDF file
ZMZainab Hussein Mohsein
Zainab Hussein Mohsein
WJWaleed K. Jawad
Waleed K. Jawad
AAAseel H. Abed
Aseel H. Abed
The manufacturing industry heavily relies on deep drawing due to its remarkable ability to produce intricate symmetrical and asymmetrical shapes with accuracy and efficiency. This research aimed to create a deep drawing tool capable of producing a pentagonal cup measuring 41mm in diameter and 30mm in height. This was achieved by conducting numerical simulations and experimental tests using two different methods. The first method involved converting an 80mm diameter circular blank into a pentagonal cup through a drawing operation, while the second method involved redrawing a cylindrical cup into a pentagonal shape. The study also analyzed the impact of these methods on the drawing load, stress/strain distributions, and thickness distributions. The finite element method software, ANSYS 20, was employed for numerical simulations. The results showed that the first method had a significantly higher punch load than the second method. However, the pentagonal cup produced using the first method had a greater thickness reduction towards the cup wall curvature compared to those produced using the second method. Therefore, the second method was considered ideal for manufacturing a pentagonal cup because it resulted in a lower degree of thinning at the cup curvature and a more uniform distribution of thickness, stress, and strain. In conclusion, this research highlights the importance of deep drawing in the manufacturing industry and emphasizes the need to choose the appropriate forming method to achieve optimal results.

16 February 2026 in Management Systems in Production Engineering
Verified
Journal Article
Open access
PDF file
AAAhmed Basil Abdulwahhab
Ahmed Basil Abdulwahhab
AHMED Mohammed AbbasAHMED Mohammed Abbas
AHMED Mohammed Abbas
ZMZainab Hussein Mohsein
Zainab Hussein Mohsein
Electrochemical machining (ECM) is defined as a non-conventional method of manufacturing that is greatly employed in processing of materials with complex geometry which are hard to be machined, providing high accuracy and excellent surface finish. ECM is influenced to higher extent by the configuration of the electrolyte flow and design of electrode tooling. In this work, two types of electrolyte flow configurations in electrode tooling are studied and compared: straight flow and side nozzle flushing flow. The effects of these configurations on material removal rate (MRR) and surface roughness were investigated both experimentally and numerically. The results emphasize the significance of the choice of electrolyte flow configuration in improving the uniformity of ion transport, flow turbulence during machining and quick heat dissipation. According to the findings, it is clear that the hollow electrode with straight flow has the best material removal rate with a percentage increase of 4.61 percent recording a rate of 0.4352 g/min, as compared to the rigid electrode with nozzle flushing flow which records 0.416 g/min. Also, the hollow electrode at straight flow showed the least extreme surface roughness, a percentage decrease of 28.52% with the least extreme of 2.030 μm and the robust electrode surface with the nozzle flow of 2.840 μm. These findings have fundamental implications for the improvement of ECM technologies with regards to productivity, energy consumption, and accuracy of machining processes. In regards to the finding, the research provides an insight into the impact customization of flow and tooling with regards to the processes in the electrochemical operation.

30 June 2023 in Al-Qadisiyah Journal for Engineering Sciences
Verified
Journal Article
Open access
PDF file
ZMZainab Hussein Mohsein
Zainab Hussein Mohsein
AAAhmed Basil Abdulwahhab
Ahmed Basil Abdulwahhab
DNDiana Abed Alkareem Noori
Diana Abed Alkareem Noori
In machining operations, surface roughness (Ra) is an essential measure of product quality. It is determined by the cutting settings. The parameters that have been worked on are the Feed (F) (0.72, 0.88, 0.96, 1.12 mm/min), depth of cut (DOC) (0.5mm), and spindle speed (N) (545, 710, 1000, 1400 r.p.m). Three types of ferrous metals were employed in this study low-carbon steel St 3, medium-carbon steel St 45, and high-carbon steel Y8. According to the data, the optimal operating condition for obtaining the best surface roughness is 1.119 µm for low-carbon steel. St 3 from the product is by employing the following cutting settings for the cutter (feed 0.72 = mm/rev), (DOC= 0.5mm), and (machine speed =1400 rpm). But when using the cutting variables (feed 1.12 = mm/rev), (DOC = 0.5mm), and (machine speed = 545 rpm) for high-carbon steel Y8, gives the highest surface roughness is 4.999 µm . The experimental findings indicate that the surface roughness of turned components is considerably affected by cutting settings and machine equipment. According to the results of this study, increasing spindle speed lowered the Ra of the turned components, but rising feed increased the surface roughness. The value acquired by this approach will benefit other researchers for future work on tool vibrations, cutting forces, and so on.