The basal mass balance of the Amery Ice Shelf (AIS) in East Antarctica is investigated using a numerical ocean model. The main improvements of this model over previous studies are the inclusion of frazil formation and dynamics, tides and the use of the latest estimate of the sub‐ice‐shelf cavity geometry. The model produces a net basal melt rate of 45.6 Gt year−1 (0.74 m ice year−1) which is in good agreement with reviewed observations. The melting at the base of the ice shelf is primarily due to interaction with High Salinity Shelf Water created from the surface sea‐ice formation in winter. The temperature difference between the coldest waters created in the open ocean and thein situ freezing point of ocean water in contact with the deepest part of the AIS drives a melt rate that can exceed 30 m of ice year−1. The inclusion of frazil dynamics is shown to be important for both melting and marine ice accretion (refreezing). Frazil initially forms in the supercooled water layer adjacent to the base of the ice shelf. The net accretion of marine ice is 5.3 Gt year−1, comprised of 3.7 Gt year−1 of frazil accretion and 1.6 Gt year−1 of direct basal refreezing.
23 March 2012 in Journal of Geophysical Research: Earth Surface
The Amery Ice Shelf, East Antarctica, undergoes high basal melt rates near the southern limit of its grounding line where 80% of the ice melts within 240 km of becoming afloat. A considerable portion of this later refreezes downstream as marine ice. This produces a marine ice layer up to 200 m thick in the northwest sector of the ice shelf concentrated in a pair of longitudinal bands that extend some 200 km all the way to the calving front. We drilled through the eastern marine ice band at two locations 70 km apart on the same flowline. We determine an average accretion rate of marine ice of 1.1 ± 0.2 m a−1, at a reference density of 920 kg m−3 between borehole sites, and infer a similar average rate of 1.3 ± 0.2 m a−1 upstream. The deeper marine ice was permeable enough that a hydraulic connection was made whilst the drill was still 70–100 m above the ice-shelf base. Below this marine close-off depth, borehole video imagery showed permeable ice with water-filled cavities and individual ice platelets fused together, while the upper marine ice was impermeable with small brine-cell inclusions. We infer that the uppermost portion of the permeable ice becomes impermeable with the passage of time and as more marine ice is accreted on the base of the shelf. We estimate an average closure rate of 0.3 m a−1 between the borehole sites; upstream the average closure rate is faster at 0.9 m a−1. We estimate an average porosity of the total marine ice layer of 14–20%, such that the deeper ice must have even higher values. High permeability implies that sea water can move relatively freely through the material, and we propose that where such marine ice exists this renders deep parts of the ice shelf particularly vulnerable to changes in ocean properties.
Laboratory creep deformation experiments have been conducted on initially isotropic laboratory-made samples of polycrystalline ice. Steady-state tertiary creep rates, , were determined at strains exceeding 10% in either uniaxial-compression or simple-shear experiments. Isotropic minimum strain rates, , determined at ˜1 % strain, provide a reference for comparing the relative magnitude of tertiary creep rates in shear and compression through the use of strain-rate enhancement factors, E, defined as the ratio of corresponding tertiary and isotropic minimum creep rates, i.e. . The magnitude of strain-rate enhancement in simple shear was found to exceed that in uniaxial compression by a constant factor of 2.3. Results of experiments conducted at octahedral shear stresses of to = 0.040.80 MPa indicate a creep power-law stress exponent of n = 3 for isotropic minimum creep rates and n = 3.5 for tertiary creep rates. The difference in stress exponents for minimum and tertiary creep regimes can be interpreted as a t0 stress-dependent level of strain-rate enhancement, i.e. .The implications of these results for deformation in complex multicomponent stress configurations and at stresses below those used in the current experiments are discussed.