This study proposes a recursive fast terminal sliding mode control (FTSMC) for a low‐voltage microgrid system operating in grid connected and islanding mode of operation. The microgrid is presumed to be a higher order distribution system. A recursive approach of FTSMC is used in the voltage source inverter to control the bus voltage nearer to the main grid and farther away from the micro source in a grid connected system. Using this methodology good tracking of the bus voltage in case of grid connection and output voltage in case of islanding mode with a faster convergence is observed. The controlled voltage has low total harmonic distortion and small steady‐state error. The algorithm requires only single voltage sensing requirement for control operation. This study also reveals the inability of the classical sliding mode control for regulating the bus voltage which is at a far end of the microgrid system. The PSCAD/EMTDC software (version 4.2) has been used for simulation studies. The experimental results are shown for a scaled down model using LabVIEW programmed field‐programmable gate array controller in islanded mode of operation to verify the performance of the proposed FTSMC.
The performance of electric drive propulsion systems is often degraded by the high torque and flux ripples of an electric drive. Traditional control methods, such as proportional plus integral (PI) controllers and classical sliding mode controllers (SMCs), have shown good response and reduced torque ripple, but even lower ripple content at low voltage levels is required for its effective use in electric vehicle (EV) applications. In this paper, a new direct torque control (DTC) technique with space vector pulse width modulation (SVPWM) using fractional-order sliding mode control (FOSMC) for a two-level inverter (2LI) at constant switching frequency is proposed. The effectiveness of this proposed controller is compared with a conventional proportional-integral controller and a conventional sliding mode controller (SMC). Simulink models are developed using MATLAB version R2018a to analyze the robustness of the proposed control strategy. Simulation results demonstrate the advantage of the proposed controller in reducing the torque ripples at steady state with less settling time during sudden load change conditions. The proposed control technique also demonstrates better utilization of the stator flux through flux trajectory waveforms.
The present manuscript concentrates on the application of Fog computing to a Smart Grid Network that comprises of a Distribution Generation System known as a Microgrid. It addresses features and advantages of a smart grid. Two computational methods for on-demand processing based on shared information resources is discussed. Fog Computing acts as an additional layer of computational and/or communication nodes that offload the Cloud backend from multi-tasking while dealing with large amounts of data. Both Fog computing and Cloud computing hierarchical architecture is compared with respect to efficient utilization of resources. To alleviate the advantages of Fog computing, a Fog computing framework based on Intel Edison is proposed. The proposed architecture has been hardware implemented for a microgrid system. The results obtained show the efficacy of Fog Computing for smart grid network in terms of low power consumption, reduced storage requirement and overlay analysis capabilities.
24 June 2014 in International Journal of Electronics
In this article, a new control methodology of sliding-mode control (SMC) for voltage source inverter (VSI)-based higher-order circuit is proposed. In this method, the SMC is used at the inner terminals for stable tracking of the voltage and current variables. An outer voltage control loop is included to reduce the steady-state error in tracking the reference load voltage. It is shown that when the SMC is applied on the load voltage terminal for higher-order VSI circuits, it leads to the instability. However, it well stabilises the system when the controller is implemented on the inner shunt capacitor terminals. Additional outer voltage control loop with proportional plus integral controller will ensure regulated voltage across the load. It has been shown that the controller is able to achieve good tracking accuracy with an acceptable stability margins. The performance of the proposed SMC has been verified on the fourth-order VSI circuit.
This study presents a reduced state feedback sliding‐mode current controller (RSFSMCC) for a voltage source inverter (VSI)‐based higher‐order circuit. The proposed controller consists of an inner current loop and an outer voltage loop. The reference for the inner input inverter current is generated from the outer voltage loop through a proportional plus integral controller. The stability of the system is ensured by using feedback of only two state variables, that is, input inverter current and output capacitor voltage of the VSI circuit. A reduced state feedback analysis is used to obtain the gain matrix for the higher‐order circuit. The tracking control convergence criterion of the system is examined through the eigen values of the resultant state matrix derived for the VSI circuit. The frequency response plot shows that the proposed RSFSMCC is robust with good stability margins. The simulation results show that the output voltage well tracks the reference voltage with reduced steady‐state error for both linear and non‐linear loads. The simulation results obtained in power systems CAD/electromagnetic transients including DC (PSCAD/EMTDC) v4.2.1 software are verified through the experimental results conducted on a single‐phase VSI circuit using field programmable gate array implementation of the RSFSMCC.
This paper demonstrates a second order sliding mode control for a voltage source inverter. A super twisting control algorithm (STA) is used to control the output ac voltage of the voltage source inverter circuit. Using the algorithm tracking of the output voltage is observed with small steady state error. The controller is found to be robust against sudden changes in the load. The output voltage waveform carries less harmonic content. The frequency response analysis shows good stability properties. PSCAD/EMTDC version 4.2 is used for simulation studies. A comparison is also brought about between the classical sliding mode control and the proposed second order sliding mode controller.