Misarah Abdelaziz

Dr. Misarah Abdelaziz

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 April 2022 in Journal of Fluid Mechanics
Verified
Journal Article
Closed access
PDF file
MAMisarah Abdelaziz
Misarah Abdelaziz
LDL. Djenidi
L. Djenidi
MGMergen H. Ghayesh
Mergen H. Ghayesh
RCRey Chin
Rey Chin
The effects of different geometries of two-dimensional (2-D) roughness elements in a zero pressure gradient (ZPG) turbulent boundary layer (TBL) on turbulence statistics and drag coefficient are assessed using single hot-wire anemometry. Three kinds of 2-D roughness are used: (i) circular rods with two different heights, $k= 1.6$ and 2.4 mm, and five different streamwise spacing of $s_{x}= 6k$ to $24k$ , (ii) three-dimensional (3-D) printed triangular ribs with heights of $k= 1.6$ mm and spacing of $s_{x}= 8k$ and (iii) computerized numerical control (CNC) machined sinewave surfaces with two different heights, $k= 1.6$ and 2.4 mm, and spacing of $s_{x}= 8k$ . These roughnesses cover a wide range of ratios of the boundary layer thickness to the roughness height ( $23 < \delta /k < 41$ ), where $\delta$ is the boundary layer thickness. All roughnesses cause a downward shift on the wall-unit normalised streamwise mean velocity profile when compared with the smooth wall profiles agreeing with the literature, with a maximum downward shift observed for $s_{x}= 8k$ . In the fully rough regime, the drag coefficient becomes independent of the Reynolds number. Changing the roughness height while maintaining the same spacing ratio $s_{x}/k$ exhibits little influence on the drag coefficient in the fully rough regime. On the other hand, the effective slope $(ES)$ and the height skewness $(k_{sk})$ appear to be major surface roughness parameters that affect the drag coefficient. These parameters are used in a new expression for $k_{s}$ , the equivalent sand grain roughness, developed for 2-D uniformly distributed roughness in the fully rough regime.

1 January 2024 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
MAMisarah Abdelaziz
Misarah Abdelaziz
LDL. Djenidi
L. Djenidi
MGMergen H. Ghayesh
Mergen H. Ghayesh
RCRey Chin
Rey Chin
One of the long-standing goals of rough wall fluid dynamics research is to determine the drag penalty of surfaces based solely on their topographical parameters. The most important length scale or roughness parameter that best describes a surface in relation to friction drag has not been agreed upon yet, despite the many studies that, over the years, have attempted to identify the most appropriate surface parameter. The concept of an equivalent sand-grain roughness (ks) was introduced to standardize different types of roughness in wall-bounded turbulence, serving as an input parameter for predicting the roughness function ΔU+. To anticipate ΔU+ generated by a rough surface under turbulent flow conditions, experts use roughness correlations that establish a correspondence between the topographical characteristics of the surface and ks. Therefore, a chronological compilation of roughness correlations is presented, detailing the parameter ranges and types of roughness used in their development. This study evaluates the effectiveness of predictive correlation functions and aims to formulate a universal function by exploring a comprehensive assortment of three-dimensional (3D) surface textures available in the literature. The results suggest that a correlation based on surface height skewness (ksk) and streamwise effective slope (ESx) can predict the ratio (ks/kq), where kq is the root mean square roughness height for 3D roughness in the fully rough regime. Despite the fact that the correlation is restricted to 3D surface roughness, which is a more realistic representation, the model demonstrated a high level of accuracy in predicting ks for over 120 distinct rough surfaces.

1 May 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
MAMisarah Abdelaziz
Misarah Abdelaziz
LDL. Djenidi
L. Djenidi
MGMergen H. Ghayesh
Mergen H. Ghayesh
RCRey Chin
Rey Chin
The impact of roughness skewness (ksk) on turbulent boundary layer (TBL) flow with a zero pressure gradient over three-dimensional (3D) sinusoidal rough surfaces was experimentally investigated using a single hotwire anemometer. Nine 3D sinusoidal profiles were manufactured with positive, negative, and zero roughness skewness values. Measurements were taken at three different freestream velocities for each surface and compared with smooth wall TBL results. This study covered a range of friction Reynolds numbers (Reτ) from approximately 1000 to 4000, with δ/k≈20 ± 2, where δ represents the local boundary layer thickness, and k is the maximum height of the roughness, measured from the valley to peak. The results indicate that the wall-unit normalized streamwise mean velocity profiles for all rough surfaces exhibit a downward shift compared to the smooth wall profiles. Surfaces with positive roughness skewness produced the highest drag, leading to the largest downward shift. The friction coefficient (Cf) decreased as ksk decreased. The percentage increase in Cf and ΔU+ (the roughness function) was much larger when moving from negative to zero roughness skewness than when moving from zero to positive roughness skewness. The small differences in turbulence intensity profiles and higher-order turbulence statistics in the outer region of the TBL support the outer layer similarity hypothesis for the roughness considered in this study. The autocorrelation study revealed that surfaces with positive roughness skewness tend to shorten the average length of turbulence structures in the near-wall region.

1 February 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
MAMisarah Abdelaziz
Misarah Abdelaziz
LDLyazid Djenidi
Lyazid Djenidi
MGMergen H. Ghayesh
Mergen H. Ghayesh
RCRey Chin
Rey Chin
A developing zero pressure gradient (ZPG) turbulent boundary layer (TBL) over different three-dimensional (3-D) sinewave roughnesses is investigated experimentally using single hot-wire anemometry. Seven different sinewave profiles are fabricated with the same amplitude and with different wavelengths in the streamwise (sx) and spanwise (sz) directions. The effects of varying sx and sz on turbulence statistics and the drag coefficient (Cf) are assessed. The wall-unit normalised streamwise mean velocity profile is shifted downwards compared with the smooth wall profile for all roughnesses. The streamwise spacing to height ratio sx/k has a more significant effect on the roughness function ΔU+ and Cf compared with the spanwise spacing to height ratio sz/k. However, sz/k has a large impact on the streamwise turbulence intensities in the log and outer layer. An excellent collapse is observed among the mean streamwise velocity profiles plotted in defect form in the outer region. However, a lack of similarity between TBLs over different rough surfaces is observed in the outer region for the turbulenceintensities profiles. For isotropic 3-D sinusoidal roughness (equal streamwise and spanwise spacing to height ratios), the contours of premultiplied streamwise turbulent energy spectrograms show an increase of energy in the outer layer with increasing spacing to height ratios. For anisotropic 3-D sinusoidal roughness (unequal streamwise and spanwise spacing to height ratios), the contours of premultiplied streamwise turbulent energy spectrograms show an increase of energy in the outer layer with increasing sz/sx from half to two in this study.

23 November 2016 in Procedia Engineering
Verified
Journal Article
Open access
PDF file
MAMuhammad A. Awad
Muhammad A. Awad
ARAhmad A. Rushdi
Ahmad A. Rushdi
MAMisarah Abdelaziz
Misarah Abdelaziz
SMScott A. Mitchell
Scott A. Mitchell
AMAhmed H. Mahmoud
Ahmed H. Mahmoud
MEMohamed S. Ebeida
Mohamed S. Ebeida
In this paper, we present a new algorithm for all-hex meshing of domains with multiple regions without post-processing cleanup. Our method starts with a strongly balanced octree. In contrast to snapping the grid points onto the geometric boundaries, we move points a slight distance away from the common boundaries. Then we intersect the moved grid with the geometry. This allows us to avoid creating any flat angles, and we are able to handle two-sided regions and more complex topologies than prior methods. The algorithm is robust and cleanup-free; without the use of any pillowing, swapping, or smoothing. Thus, our simple algorithm is also more predictable than prior art.

17 October 2025 in International Journal of Wildland Fire
Verified
Journal Article
Open access
PDF file
MAMisarah Abdelaziz
Misarah Abdelaziz
ASAndrew Sullivan
Andrew Sullivan
Background: Burning debris (firebrands) can potentially travel significant distances to ignite spot fires many kilometres downwind of a wildfire, posing substantial challenges for fire spread prediction and management. Aim: To improve our understanding of the combustion and flight behaviours of common bark firebrands through better quantification and detailed analysis of their motion, combustion and aerodynamic behaviour. Methods: A custom firebrand tracking system consisting of three synchronised video cameras positioned orthogonally around the working section of a vertical wind tunnel was built and bespoke image processing algorithms developed to automatically reconstruct the 3D trajectory and combustion behaviour of a bark sample. Key results: The system was found to accurately estimate bark sample position as well as spatial velocity, orientation changes and burnout profile. Conclusions: A robust and accurate methodology to track the dynamic trajectory and behaviour of untethered burning bark falling at its terminal velocity was developed that overcomes many of the limitations of previous tracking approaches. Implications: This study, applicable to a broad range of bark species as well as other firebrand materials under varying conditions, enables the development of more accurate predictive models of firebrand transport that will help improve the simulation and prediction of spotting in wildfires.