Loess landslides induced by the freeze–thaw effect frequently occur in Yili, China. Freeze–thaw cycles cause indelible changes in the soil microstructure, affecting its permeability. This study investigated the impacts of freeze–thaw cycles on the permeability of Yili loess using permeability tests on undisturbed (virgin, in situ) and remolded loess samples taken before and after freeze–thaw cycles. Scanning electron microscopy and nuclear magnetic resonance techniques were utilized to investigate the microscopic mechanism of the freeze–thaw process on the loess. Grey relation analysis (GRA) was employed to analyze the correlation between macroscopic permeability and microscopic parameters (maxi. radius, eccentricity, fractal dimension, directional probability entropy, and porosity). The results revealed that the permeability and all the microstructure parameters have roughly shown the same trend: “fluctuation–towards equilibrium–stability”. Firstly, the permeability coefficients of original and remolded loess experienced three and two peaked–trends, respectively, before 30 freeze–thaw cycles. The trends eventually stabilized within 30–60 freeze–thaw cycles. Increased number of freeze–thaw cycles disintegrated large particles in undisturbed loess into medium–sized particles, and particle shapes became more uncomplicated. Medium–sized particles in the remolded loess agglomerated to larger particles with more complex shapes. Furthermore, the overall porosity of the originally undisturbed loess decreased, and large and medium–sized pores transformed into small pores and micropores. In contrast, the overall porosity of remolded loess increased. Finally, the results revealed that permeability coefficients of the undisturbed and remolded loess became closely related with eccentricity and porosity, respectively. This study provides a reference for preventing and governing the loess landslides induced by the freeze–thaw cycles and permeability reduction in construction on loess in seasonally frozen areas in Yili.

This research examined the drying–wetting cycles induced changes in undrained triaxial shear strength parameters and microstructural changes of Yili loess. The drying–wetting cycles were selected as 0, 1, 3, 5, 10, 20 and 30. Then, we collected Yili loess samples and performed unconsolidated-undrained (U-U) triaxial shearing tests to ascertain the variation in shear strength parameters with drying–wetting cycles. Additionally, we investigated the microstructural changes of Yili loess samples under drying–wetting cycles simultaneously via nuclear magnetic resonance (NMR) and scanning electron electroscopy (SEM). Finally, we established a grey correlation model between shear strength and microstructural parameters. Under U-U conditions, the prime finding was that the loess’s shear strength parameters changed overall after drying–wetting cycles; in particular, the internal friction angle φ dropped significantly while the cohesion c changed only slightly during cycles. For all the cycles, the first cycle gave the highest change. Soil morphology deterioration was evident at the initial stage of cycles. During the entire drying–wetting cyclic process, pore size distribution showed progressive variance from two-peak to a single-peak pattern, while both porosity and the fractal dimension of pores increased gradually towards stability. Soil particle morphology became slowly simple and reached the equilibrium state after 20 drying–wetting cycles. Under cyclic drying–wetting stress, the shear strength parameter changes were significantly correlated to microstructural modifications. This investigation was related to loess in the westerly region. The findings were expected to provide new insight into establishment of the connection between microstructure and macro stress–strain state of loess. To some extent, it provided a theoretical basis for the prevention and control of loess engineering geological disasters in Yili, Xinjiang and other areas with similar climate and soil types.

Loess landslides caused by the dry-wet cycling processes are the most common geological disasters in the Yili region of China and have caused significant economic loss and casualties. Therefore, there is an urgency to study the mechanism of landslide disasters. However, research on loess landslide disasters under dry-wet cycling conditions in the Yili River Valley is still underdeveloped, and the research foundations are relatively weak. Based on the characteristics of high and stable mica content in Yili loess, this research probed the changes in shear strength and microstructure of loess with different mica contents (0%, 5%, 10%, and 15%) after different dry-wet cycles (0, 1, 3, 5, 7, 10, 15, and 20) using direct shear testing and a scanning electron microscopy. The results showed that the mica content had a negative relationship with the shear strength of loess. For the same number of dry-wet cycles, the higher the mica content was, the lower the loess’ shear strength, especially in the first five dry-wet cycles. The influence of mica content on shear strength parameters was not similar. The impact was more significant for cohesion. With increased mica content, cohesion gradually decreased. The effect was minor with the internal friction angle. With the rise in mica content, the angle slightly increased with slight variations. Under certain dry-wet cycling conditions, micro-particle content in the loess decreased continuously, the average reduction can reach 11.25%, the content of small and medium particles tends to increase, the average increments were 6.21% and 3.1%, and volatility changes in large particle content. However, the overall increasing trend remains. Accordingly, the number of micropores and small pores decreased, the average reduction was 7.63% and 5.48%, the number of medium pores and large pores increased, and the average increments were 6.13% and 6.99%, respectively. All these changes were more evident in the first three dry-wet cycles and when the mica content increased from 0% to 5%. This study will be beneficial as a reference for the occurrence mechanisms of loess landslide under dry-wet cycling conditions in the Yili area.

In practical engineering, the development of surface cracks is one of the most important reasons for the destruction of the rock mass, and the development of complex morphology fractures on the rock mass surface significantly influences rock mass mechanics. This paper addresses the freeze–thaw damage issue in rock mass containing surface fractures in cold regions. Tuffs and a control group are selected as research samples, with the control group being prefabricated surface jointed specimens with an inclination angle of 70° and a fracture depth ratio d (crack depth) /t (sample width) of 0.26. The study analyzes the mass, wave velocity loss, macro-microcosmic fracture damage morphology, and mechanical properties of the two specimen groups through laboratory freeze–thaw cycle tests, uniaxial compression tests, and scanning electron microscopy examinations. The results show an overall decrease in mass, wave velocity, and uniaxial compressive strength as the cycle number increases, with the prefabricated jointed group samples showing more significant changes. However, the two specimen groups exhibit different macroscopic failure fracture states. In addition, scanning electron microscopy images illustrate that after freeze–thaw cycles, the large rock mass particles break into smaller fragments, resulting in looser particle arrangements and a transition from initial surface cementation to point contact., which weakens the compressive strength of the rock mass. The paper also explains the mechanism of the diminishing impact of freeze–thaw cycles on the strength of the rock mass after a certain number of cycles. The research outcomes hold significant reference value for engineering construction in cold regions.

To clarify the development and height of the fractured water-conducting zone of underground mines with weakly cemented overburden, the W8203 working face of the Tashidian Erjingtian Mine in Xinjiang, China, was selected to carry out a case study. Firstly, a physical analog model test was conducted to investigate the development law of the water-conducting fracture zone, followed by a numerical simulation via the PFC2D program. Afterward, a theoretical analysis based on the key stratum theory was carried out. The results demonstrated that there were one primary key stratum and three sub-key strata upon the W8203 working face. As verified by the physical analog tests, the water-conducting fracture developed to the bottom of the primary key stratum, and the height of the fractured water-conducting zone was 246.38 m. The numerical analysis suggests that the primary key stratum did not completely break and the fracture did not penetrate the stratum. Theoretical calculation indicated that the primary key stratum maintained stability in the structure without any breakage. The height of the fractured water-conducting zone is comprehensively determined to be 246.38 m, which is relatively close to the measured value (229.32 m). Based on the prediction method of key stratum position combined with the characteristics of weak cemented overburden, a method to predict the height of a water-conducting fracture zone suitable for weak cemented overburden was developed. The accuracy of this method was also verified through an in-depth comparison with field test results. Under the background of the “strategic westward shift” of coal resource exploration and development in China, the research results can provide theoretical and technical support for safe production in the Tashidian Mining Area and references for green and safe production in weakly cemented overburden mining areas in western China.

Landslides frequently occur in the loess-rich Yili region of Xinjiang, China, due to the combined effects of wetting-drying and freeze-thaw (WD-FT) cycles, which cause changes in the soil/loess internal structure and shear strength. This paper explores the combined effect of WD-FT cycles on the shear strength evolution of Yili loess through cyclic and triaxial shear tests. The micromechanism of the effect of WD-FT cycles on the loess properties is studied through scanning electron microscopy tests. Finally, the gray correlation analysis method assesses the correlation between relevant macro and micro parameters. The results show that: (1) With the increase in WD-FT cycles, the cohesion of loess decreases first and then gradually stabilizes, while the internal friction angle first grows and then drops before stabilizing. This indicates that the WD-FT cycles cause different degrees of decline in the soil’s internal friction angle and cohesion. (2) As the number of WD-FT cycles increases, the average abundance and directional probability entropy fluctuate slightly, gradually decreasing and stabilizing. In contrast, the particle size dimensionality gradually decreases and stabilizes, and the pore area ratio first increases and then gradually stabilizes. (3) Six microstructural parameters (average diameter, average abundance, particle size dimensionality, directional probability entropy, particle roundness, and pore area) are selected for correlation analysis with the shear strength index of loess. The results show that the particle size dimensionality closely correlates with macroscopic internal friction angle under coupled cycling, while the pore area closely correlates with macroscopic cohesion. These findings are instrumental in preventing and controlling loess landslides caused by WD-FT cycles in the Yili region of Xinjiang, China, and similar loess-rich regions.