Shear fractures can facilitate fluid conductivity through rock. Aperture and roughness are controlling characteristics for a fracture's fluid conductivity. Inspired by en echelon fractures, we develop a shear “fracturelet” model that predicts anisotropic aperture with respect to the direction of shearing, rougher (nonplanar) rather than smoother (planar) fractures, and the bounds of this roughness for a coalesced fracture. This tendency for rougher fracture creation is validated by in situ X‐ray images and fluid conductivity measurements from triaxial direct shear experiments on anhydrite and shale. These experiments were conducted at confining stresses from 4 to 30 MPa and shear displacement magnitudes from 0 to 2 mm on initially intact rock specimens. Hydraulic, dilatational, and local fracture apertures were measured in the experiments. Apertures exhibited strong anisotropy with more conductive flow paths forming perpendicular to the direction of shearing. Local and dilatational aperture were found to be positively correlated with increasing shear displacement but hydraulic aperture was found to vary significantly, always having values smaller than the other aperture measures at factors ranging from 0.6 to 0.0. An implication of these results is that shear fractures have a mechanism for simultaneously exhibiting very low fluid conductivity and high fluid storage volume.

Target subsurface reservoirs for emerging low‐carbon energy technologies and geologic carbon sequestration typically have low permeability and thus rely heavily on fluid transport through natural and induced fracture networks. Sustainable development of these systems requires deeper understanding of how geochemically mediated deformation impacts fracture microstructure and permeability evolution, particularly with respect to geochemical reactions between pore fluids and the host rock. In this work, a series of triaxial direct shear experiments was designed to evaluate how fractures generated at subsurface conditions respond to penetration of reactive fluids with a focus on the role of mineral precipitation. Calcite‐rich shale cores were directly sheared under 3.5 MPa confining pressure using BaCl₂‐rich solutions as a working fluid. Experiments were conducted within an X‐ray computed tomography (xCT) scanner to capture 4‐D evolution of fracture geometry and precipitate growth. Three shear tests evidenced nonuniform precipitation of barium carbonates (BaCO₃) along through‐going fractures, where the extent of precipitation increased with increasing calcite content. Precipitates were strongly localized within fracture networks due to mineral, geochemical, and structural heterogeneities and generally concentrated in smaller apertures where rock:water ratios were highest. The combination of elevated fluid saturation and reactive surface area created in freshly activated fractures drove near‐immediate mineral precipitation that led to an 80% permeability reduction and significant flow obstruction in the most reactive core. While most previous studies have focused on mixing‐induced precipitation, this work demonstrates that fluid–rock interactions can trigger precipitation‐induced permeability alterations that can initiate or mitigate risks associated with subsurface energy systems.

We present hydro‐mechanical measurements that characterize shear on natural fractures in schist, amphibolite, and rhyolite specimens from the enhanced geothermal system (EGS) Collab Project's Experiment 1 and 2 sites (E1 and E2) at the Sanford Underground Research Facility. We employed a triaxial direct shear method augmented with X‐ray imaging to perform hydroshearing (injection‐induced shearing) and mechanical shearing on naturally fractured specimens at in situ stress conditions. Measurements included fracture permeability, strength, stress‐dependent aperture, shear dilation, and frictional strength. Results reveal that in situ natural fractures must be permeable, weak, and shear‐oriented to be hydrosheared, and only a subset of the observable in situ fractures were suitable. When sheared, the fracture permeability typically increased by a factor of 10 or more and this increase was retained over time. However, shear slip did not always result in permeability increase. High phyllosilicate content associated with exceptionally weak fractures exhibited poor or even decreased permeability after stimulation. These measurements in combination with site data were used to conduct a slip‐tendency analysis for different fracture sets, and we selected the top candidate natural fractures for hydroshearing at the EGS Collab sites. We also found that the lower in situ shear stress and stronger fractures at the E2 site make hydroshearing more challenging than at the E1 site. Overall, the methods and analysis used in our work can be applied to any geothermal project to identify in situ joint sets that are best suited for hydroshearing, which in turn can help to optimize well placement and energy production.

Fluid injection into rock formations can either produce complex branched hydraulic fractures, create simple planar fractures, or be dominated by porous diffusion. Currently, the optimum injection parameters to create branched fractures are unknown. We conducted repeatable hydraulic fracturing experiments using analog‐rock samples with controlled heterogeneity to quantify the fluid parameters that promote fracture branching. A large range of injection rates and fluid viscosities were used to investigate their effects on induced fracture patterns. Paired with a simple analytical model, our results identify the threshold at which fracture transitions from an isolated planar crack to branched cracks when closed natural fractures exist. These results demonstrate that this transition can be controlled by injection rate and fluid viscosity. In relation to the field practices, the present model predicts slickwater and lower viscosity fluid injections promote fracture branching, with the Marcellus shale used as an example.