Cells form stress granules (SGs) upon stress stimuli to protect sensitive proteins and RNA from degradation. In the yeast Saccharomyces cerevisiae, specific stresses such as nutrient starvation and heat shock were recently shown to trigger recruitment of the yeast pyruvate kinase Cdc19 into SGs. This RNA-binding protein was shown to form amyloid-like aggregates that are physiologically reversible and essential for cell cycle restart after stress. Cellular Cdc19 exists in an equilibrium between a homo-tetramer and monomer state. Here, we show that Cdc19 aggregation in vitro is governed by protein quaternary structure, and we investigate the physical-chemical basis of Cdc19’s assembly properties. Equilibrium shift towards the monomer state exposes a hydrophobic low complexity region (LCR), which is prone to induce intermolecular interactions with surrounding proteins. We further demonstrate that hydrophobic/hydrophilic interfaces can trigger Cdc19 aggregation in vitro. Moreover, we performed in vitro biophysical analyses to compare Cdc19 aggregates with fibrils produced by two known dysfunctional amyloidogenic peptides. We show that the Cdc19 aggregates share several structural features with pathological amyloids formed by human insulin and the Alzheimer disease-associated Abeta42 (Aβ42) peptide, particularly secondary β-sheet structure, thermodynamic stability, and staining by the Thioflavin T dye. However, Cdc19 aggregates could not seed aggregation. These results indicate that Cdc19 adopts an amyloid-like structure in vitro that is regulated by the exposure of a hydrophobic LCR in its monomeric form. Together, our results highlight striking structural similarities between functional and dysfunctional amyloids and reveal the crucial role of hydrophobic/hydrophilic interfaces in regulating Cdc19 aggregation.
Safety concerns related to the use of potentially explosive, liquid organic electrolytes in commercial high-power lithium-ion batteries are constantly rising. One promising alternative is to use thermally stable ionic liquids (ILs) as conductive media, which are however, limited by low ionic conductivity at room temperature. This can be improved by adding fillers, such as silica or alumina nanoparticles (NPs), in the polymer matrix that hosts the IL. To maximize the effect of such NPs, they have to be uniformly dispersed in the matrix while keeping their size as small as possible. In this work, starting from a water dispersion of silica NPs, we present a novel method to incorporate silica NPs at the nanoscale level (<200 nm) into PVdF-HFP polymer clusters, which are then blended with the IL solution and hot-pressed to form separators suitable for battery applications. The effect of different amounts of silica in the polymer matrix on the ionic conductivity and cyclability of the separator is investigated. A membrane containing 10 wt.% of silica (with respect to the polymer) was shown to maximize the performance of the separator, with a room temperature ionic conductivity of of 1.22 mS cm . The assembled half-coin cell with LiFePO and Li as the cathode and the anode exhibited a capacity retention of more than 80% at a current density of 2C and 60 C.
In the last decades bioresorbable and biodegradable polymers have gained a very good reputation both in research and in industry thanks to their unique characteristics. They are able to ensure high performance and biocompatibility, at the same time avoiding post-healing surgical interventions for device removal. In the medical device industry, it is widely known that product formulation and manufacturing need to follow specific procedures in order to ensure both the proper mechanical properties and desired degradation profile. Moreover, the sterilization method is crucial and its impact on physical properties is generally underestimated. In this work we focused our attention on the effect of different terminal sterilization methods on two commercially available poly(l-lactide-co-ε-caprolactone) with equivalent chemical composition (70% PLA and 30% PCL) and relatively similar initial molecular weights, but different chain arrangements and crystallinity. Results obtained show that crystallinity plays a key role in helping preserve the narrow distribution of chains and, as a consequence, defined physical properties. These statements can be used as guidelines for a better choice of the most adequate biodegradable polymers in the production of resorbable medical devices.
Redispersible powders based on soft core-hard shell polymer particles can be used as additives in polymer-cement mortars. The role of this morphology on the spray-drying production of these powders and on the crack-bridging properties of the corresponding cement-based membranes is investigated. Different polymer latexes at high solid content with varied core-shell ratio, shell thickness and chemical composition (hardness) were prepared from styrene and 2-ethylhexyl acrylate monomers via semi-batch emulsion polymerization. The latexes were characterized in terms of size, composition, and glass transition temperature (T ), and spray-dried to obtain redispersible polymer powders (RPPs) using poly (vinyl alcohol) and limestone powder as anti-caking agents. The polymer powders were mixed with a mortar mixture and redispersed in water to produce cement-based membranes, which were tested for crack-bridging properties at different temperatures. The results showed that it was not possible to spray-dry a dispersion of homogeneous polymer particles with T of −25 C, unless these particles are protected by much harder (high T ) shell. In particular, it was observed that a thicker shell improved the spray-ability, but lowered the crack-bridging properties of the produced membrane. A trade-off between these two was revealed to be the key for the optimal design of the polymer nanoparticles, as proven by the systematic study of the core-shell morphology reported in this work. The best compromise was shown to consist of particles larger than 300 nm, shell thickness of about 5 nm, and core-shell ratio of 97%, with styrene content in the shell not larger than 80% to avoid excessive hydrophobicity.
In the last decades bioresorbable and biodegradable polymers have gained a very good reputation both in research and in industry thanks to their unique characteristics. They are, indeed, able to ensure high performances and biocompatibility, at the same time avoiding post-healing surgical interventions for devices removal. In the medical device industrial use of such biopolymers, it is widely known that product formulation and manufacturing need to follow specific procedures in order to ensure both proper mechanical properties and desired degradation profile. Moreover, also the sterilization method is crucial and its impact on physical properties is generally underestimated. In this work we focused our attention on the effect of different terminal sterilization methods on two commercially available poly(L-lactide-co-ε-caprolactone) with equivalent chemical composition (70% PLA and 30% PCL) and relatively similar initial molecular weight, but different chains arrangement and crystallinity. Results obtained show that crystallinity plays a key role, helping in preserving the narrow distribution of chains and, as a consequence, defined physical properties. These statements can be used as guidelines for a better choice of the most adequate biodegradable polymers in the production of resorbable medical devices.