Fast nanoindentation technology is a new method used to generate performance maps showing the hardness and elastic modulus distribution of each position, and it has become a research focus. In this paper, nanoindentation combined with scanning electron backscatter diffraction (EBSD) is used to analyze the micro-regional properties of single-phase interstitial-free (IF) steel. Hardness, elastic modulus and the orientation of a 200 μm × 200 μm area were characterized in situ. The relationships between hardness, elastic modulus and orientation were analyzed. The experimental results showed that the hardness varied from 1.25 GPa to 2.57 GPa, while the modulus varied from 122 GPa to 227 GPa with different crystallographic orientations. The hardness value of the (111) crystal plane was particularly high, with an average hardness of about 1.84 GPa, which is due to its higher work hardening rate. This result is consistent with the EBSD kernel average misorientation (KAM) micrograph. The harder locations with greater misorientation are more difficult to deform compared to locations with small hardness regions, for example, the (001) crystal plane. However, there seems to be no obvious strong relationship between modulus and orientation. The modulus of the regions with lower hardness seems to be smaller. The results of the KAM diagram are consistent with those of hardness mapping.

This study investigated the relationship between Mn segregation, damping capacity, and mechanical properties of a Mn–Cu damping alloy after aging at different temperatures. The results showed that after aging, the alloy underwent spinodal decomposition, forming Mn-segregated regions, while α-Mn precipitates appeared at the grain boundaries. The microstructure resulting from spinodal decomposition promoted martensitic transformation, created twin boundaries, and enhanced damping capacity. As the aging temperature increased, the Mn content in the Mn-rich regions gradually rose, thereby raising the martensitic transformation temperature. The twin density first increased and then decreased, which may be attributed to the precipitation and broadening of the α-Mn phase along the grain boundaries of the Mn-rich regions when the aging temperature was too high. At an aging temperature of 425 °C, the tanδ reaches a maximum of 0.05, and the martensitic transformation temperature reaches 100 °C, at which point the tanδ remains 0.04. After aging at 425 °C, a preferred orientation along develops. The [001] orientation has the largest Schmid factor, which is most favorable for the reversible motion of twin boundaries under external stress, thus achieving the highest energy dissipation. To summarize, by promoting the creation of fine {011} twins by means of spinodal decomposition and by increasing the [001] oriented grain fraction through texture development, aging enhances the damping properties of the Mn–Cu alloy. In particular, the aging at 425 °C can provide the best combination of the microstructure and texture conditions, providing the highest damping performance in a wide temperature range.

This study investigated the influence of Mn content (70 wt.%, 75 wt.%, and 80 wt.%) on the microstructure, mechanical properties and damping capacity of Mn-Cu alloys using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), mechanical testing and dynamic mechanical analysis (DMA). The results indicate that during cooling after aging, the Mn-Cu alloy undergoes martensitic transformation, resulting in a dual-phase structure of fcc and fct. The 70 wt.% Mn alloy exhibits a mixed-grain structure with mostly long, straight twin bands, while the 75 wt.% and 80 wt.% Mn alloys consist of fine equiaxed grains with mostly intersecting twin bands. The microstructure determines the properties of the alloy. As the Mn content increases, the mechanical properties initially increase and then decrease, and the 75 wt.% Mn alloy has the best mechanical performance (UTS = 534 MPa, YS = 263 MPa). In contrast, the damping capacity shows a decreasing trend, and the 70 wt.% Mn alloy exhibits the best damping capacity (tanδ = 0.064). The main damping peak of tanδ in Mn-Cu alloys is derived from the relaxation of the twin boundaries, and the less obvious secondary peak is the internal friction peak of martensitic transformation.