Sana Ullah

Mr. Sana Ullah

orcid

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 July 2026 in Chemengineering
Verified
Journal Article
Open access
PDF file
Hasnain Ali ShahHasnain Ali Shah
Hasnain Ali Shah
AUAsad Ullah
Asad Ullah
SUSana Ullah
Sana Ullah
UAUmar Abdullah
Umar Abdullah
MAMuhammad Ali
Muhammad Ali
SIShehryar Ishaque
Shehryar Ishaque
This study presents a numerical investigation of a slit fin-enhanced phase change material (PCM)-based battery thermal management system (BTMS) for an 18650 cylindrical LiNixCoγMnzO2 lithium-ion battery. The proposed design modifies the conventional solid rectangular external fins by introducing four longitudinal slit fins with uniformly distributed rectangular through-thickness slot cutouts along the fin height. This modification increases the PCM-fin interfacial contact area and creates additional natural convective heat dissipation pathways from the PCM region to the ambient environment while maintaining the same BTMS envelope, PCM thickness, fin count, housing geometry, and material selection as the validated rectangular-fin baseline. The lumped-capacitance thermal model was used for battery heat generation, while the enthalpy-porosity approach was employed to model PCM melting. Simulations were performed in ANSYS Fluent 2024/R2 at 1C, 3C, 5C, and 7C discharge rates at an ambient temperature of 308.15 K. Paraffin wax PCM with a latent heat of approximately 240,000 J/kg was used. The rectangular fin model was first validated against the baseline study, achieving an average cell wall temperature error of 1.03% and a maximum error of 1.47% at 5C, while the total temperature and liquid fraction deviations remained below 0.73%, confirming the reliability of the numerical model. Mesh independence and temporal convergence studies further confirmed that the selected 0.50 mm polyhedral mesh and 0.5 s time step provided accurate and stable results. The results demonstrate that the slit fin geometry provides metric-dependent improvements in PCM utilization, thermal protection duration, and high-rate latent-heat activation rates. At 1C, both configurations remained well below the 318.15 K safety threshold, but the slit fin configuration maintained approximately 0.7 K lower total temperature at 2500 s and delayed PCM melting by about 300 s compared with rectangular fins, preserving more latent heat capacity for later thermal loading. At 3C, the slit fin design extended the thermal protection duration from 1650 s to 2500 s, corresponding to a 51.5% improvement, and increased PCM latent heat utilization from LF = 0.42 to LF = 0.49, representing a 16.7% increase. At 5C, slit fins initiated PCM melting approximately 3.5 times earlier, around 100 s, compared with 350–400 s for rectangular fins, and reached LF = 0.50 at 620 s, whereas rectangular fins reached only LF = 0.37 at 1480 s. This corresponds to approximately 2.87 times faster PCM utilization and 35.1% greater PCM melting. At 7C, the slit fin system again showed stronger PCM engagement, corresponding to 35.7% greater PCM utilization. Temperature and liquid fraction contours confirmed that the slit openings intensify localised PCM melting near the heat source, improve heat spreading through the PCM domain, and support natural convection-assisted melting. Overall, the slit-fin geometry provides a geometry-based enhancement for PCM utilization and thermal protection without changing system size or material selection for PCM-based BTMSs, improving latent heat utilization and thermal protection without increasing system size, PCM volume, or material complexity.

4 January 2026 in Physical Education, Health and Social Sciences
Verified
Journal Article
Closed access
SUSana Ullah
Sana Ullah
AUAsad Ullah
Asad Ullah
MHMuhammad Hashir
Muhammad Hashir
MHMuhammad Huzaifa
Muhammad Huzaifa
Artificial egg incubation is important in poultry production as it controls the environmental factors on the development of embryos. Effective incubation requires a certain level of control over temperature, humidity, ventilation and egg turning. In this paper, the design and development of a semi-automated egg incubator with low cost but with standard incubation parameters mentioned in the existing literature is provided, and a dual-power (AC/DC) operating system is proposed as one of the changes. To assess experimentally, three temperature conditions were taken collectedly, i.e. T1 = 36.5 °C, T2 = 37.5 °C, and T3 = 38 °C and humidity and ventilation conditions maintained fixed. A W1209 thermostat was used to control temperature, and a water-tray-based approach with the help of forced air circulation was used to control humidity. The proposed system has an automatic inverter and battery backup unlike most of the current incubator designs that only use an AC power supply, allowing a continuous operation during power failures. When chicken eggs were experimentally tested, the hatching rate was approximately 80%. The proposed incubator has good reliability, low cost and high suitability in rural poultry farming and educational purposes.

9 October 2026 in Discover Robotics
Verified
Journal Article
Open access
PDF file
MAMohammad Ali
Mohammad Ali
SUSana Ullah
Sana Ullah
AUAsad Ullah
Asad Ullah
MKM. Danyal Khan
M. Danyal Khan
MHMubasher Hassan
Mubasher Hassan
Agriculture in developing economies such as Pakistan remains heavily dependent on manual labor and single-purpose, grid or fuel-powered machinery that is often unaffordable for smallholder farmers. This paper presents the design, fabrication, and experimental evaluation of a multifunctional, solar-powered, Internet of Things (IoT)-enabled agricultural robot capable of performing soil cultivation, seed placement, irrigation, and crop cutting within a single integrated platform. The system architecture is built around an ESP32 microcontroller that interfaces with a DHT11 temperature/humidity sensor, an HC-SR04 ultrasonic obstacle sensor, an ESP32-CAM module for visual field monitoring, an L298N dual H-bridge motor driver, and relay-controlled actuators, with energy supplied by a 20 W photovoltaic panel, a 12 V/7.2 Ah battery, and a battery management system (BMS). Mechanical subsystems comprising a tooth-type cultivator, a soil-leveling roller, a servo-actuated seed dispenser, a DC pump-based irrigation unit, and a blade-type cutter were designed in CAD, fabricated, and integrated onto a four-wheel-drive chassis. Engineering calculations were used to size the power budget, battery backup, drive-motor torque, structural factor of safety, seeding rate, and irrigation flow. Field trials show a typical operating power demand of 24.4 W against an average usable solar output of 11–12 W, a battery backup of approximately 3.5 h, The experimental results demonstrated satisfactory performance of the proposed agricultural robot, achieving an average seed-placement accuracy of 74.45% over 11 experimental trials. The developed system also successfully performed soil digging, irrigation, crop cutting, obstacle detection, and real-time IoT-based remote monitoring, demonstrating its suitability for sustainable precision agriculture.