Producing joints of aluminum and copper by means of fusion welding is a challenging task. However, the results of various studies have proven the potential of friction stir welding (FSW) for manufacturing aluminum-copper joints. Despite the proven feasibility, there is currently no series application in automotive industry to produce aluminum-copper joints for electrical contacts by means of FSW. To make FSW as efficient as possible for large-scale production, maximized welding speed is desired. Taking this into account, this paper presents results of a parametric investigation, the objective of which was to increase the welding speed for FSW of aluminum and copper in comparison to welding speeds that are considered to be state of the art. Taguchi method was used to design an experimental plan and target figures of the investigations were the resultant tensile strengths and electrical resistances. Dependencies between input parameters and target figures were determined systematically. The optimal welding parameters, at which joints failed in the weaker aluminum material, included a welding speed of 700 mm/min. Consequently, it could be shown that joints with a performance similar to those of the base materials can be obtained using significantly higher welding speeds than reported in the relevant literature.

Manufacturing dissimilar joints of aluminum and copper is a challenging task. However, friction stir welding (FSW) was found to be a suitable technique to produce aluminum–copper joints. Due to different electrical conductivities between aluminum and copper, an adjustment of the cross-section is required to realize electrical conductors free of resistive losses. Taking this into account, this paper presents initial results on the mechanical and electrical properties of friction stir butt welded aluminum and copper blanks having thicknesses of 4.7 mm and 3 mm, respectively. Three different approaches were investigated with the aim to produce sound welds with properties similar to those of the used base materials. Friction stir welding has been conducted at a welding speed of 450 mm/min. Subsequently, the welded specimens were subjected to metallographic analysis, tensile testing, and measurements of the electrical conductivity. The ultimate tensile force of the best joints was about 10 kN, which corresponds to joint efficiencies of approximately 72% of the aluminum base material. The analysis of electrical joint properties led to very promising results, so that the potential of FSW of Al–Cu butt joints with sheets having different thicknesses could be confirmed by the investigations carried out.

Although the joining of aluminum and copper is a difficult task, several studies have shown that friction stir welding (FSW) is capable of producing aluminum-copper-joints with excellent performance. Therefore, it is desirable to use this joining technique for the production of cost- and weight-reduced conductors for the automotive sector. The exposed copper contact spots in automobiles are usually coated with tin for design reasons and in order to improve their corrosion resistance. In this context, it is possible to perform the weld at first and to coat afterwards, or to weld already coated copper workpieces. Taking this into account, this paper presents results on the influence of copper-sided tinning on the joint formation as well as the achievable mechanical and electrical properties of friction stir butt welded aluminum-copper joints. Two variants were considered. The first variant included copper blanks with a tinned surface. For the second variant the surface and the abutting edge of the copper were coated. The best welds achieved excellent electrical properties and their tensile strength was only slightly reduced compared to the aluminum base material. Thus, it was shown that if these tensile strength losses are acceptable, FSW of aluminum to tin coated copper is applicable.

For large-scale manufacturing of profile-intensive vehicle bodies, a suitable joining process for hollow profile–sheet metal joints is required. These joints pose challenges related to minimizing plastic deformation while ensuring low, localized heat input to preserve the properties of high-strength steels. Conventional resistance spot welding often leads to profile deformation due to concentrated force and heat input and the lack of mechanical backing. For this reason, CD-welding tests on sandwich structures consisting of hollow profile-sheet metal with a wire mesh interlayer used as natural projections are conducted. This enables multiple small welds with localized heat input and welding times below 10 ms. This study investigates the influence of the weld parameters electrode force and charging energy, and illustrates that as the electrode force increases, plastic deformation increases up to the point of failure above 24 kN. In this regard, support structures and inserts made of copper and plastic, as well as novel welding electrodes with lateral profile contacts, are being investigated. Joint quality is evaluated based on setdown, electrical resistance, shear strength, and plastic deformation of hollow profiles. The highest shear tensile forces of up to 47 kN were achieved using 60 projections and an inner copper support structure.