Emad Etman

Prof. Dr. Emad Etman

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 February 2023 in Structures
Verified
Journal Article
Closed access
Emad EtmanEmad Etman
Emad Etman
MMMohamed H. Mahmoud
Mohamed H. Mahmoud
AHAli Hassan
Ali Hassan

17 October 2023 in Ain Shams Engineering Journal
Verified
Journal Article
Open access
AEAli F. Elkliny
Ali F. Elkliny
HSHaytham M. Sanad
Haytham M. Sanad
Emad EtmanEmad Etman
Emad Etman

1 March 2017 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
NKNesreen Kassem
Nesreen Kassem
AAAhmed Atta
Ahmed Atta
Emad EtmanEmad Etman
Emad Etman
Lateral loads annually destroy many reinforced concrete structures in different countries. However, there is a necessary need to retrofit masonry infill walls to utilize them as lateral load resisting elements. For this purpose, an experimental program has been carried out on half scale specimens to characterize the behavior of single story brick masonry in-filled frames under the effect of lateral loads. The effectiveness of different strengthening techniques is investigated using Carbon–fiber Reinforcement Polymer (CFRP). The steel reinforcement at the beam-columns joints of all specimens was detailed as hinged connection. FRP sheets and FRP strips were used as strengthening agents for the tested specimens. They were utilized in two different cases, bonded or unbonded to the masonry wall. In addition, the FRP anchor technique was used to increase the efficiency of bonding the strengthening agents with the frames and the walls. The load–displacement behavior, FRP strain, crack pattern, steel strain, and mode of failure of the tested specimens were investigated. The results showed that the used strengthening methods are effective, with high increase in strength and ductility. In addition, an analytical model was presented and solved. Based on this model, simplified empirical equation to design the required amount of FRP needed to resist lateral loads was proposed. The equation showed a good agreement with both the experimental result and finite element output.

10 April 2023 in Arabian Journal for Science and Engineering
Verified
Journal Article
Open access
PDF file
Ahmed ElsawwafAhmed Elsawwaf
Ahmed Elsawwaf
MSMostafa El Sawwaf
Mostafa El Sawwaf
ANAshraf Nazir
Ashraf Nazir
Waseim AzzamWaseim Azzam
Waseim Azzam
AFAhmed Farouk
Ahmed Farouk
Emad EtmanEmad Etman
Emad Etman
This paper used finite element modeling to evaluate the consolidation effect on the performance of existing rafts underpinned with micropiles under combined vertical and lateral loads. For this purpose, a real-life case study was discussed, in which micropile underpinning was used to stop the continuous tilt of a 13-floor residential building supported by a surface raft. It was found that the building tilted towards the northeast direction because of the consolidation of a deep soft clay layer under the northeast building corner. After discussing the as-built micropiling system, a 3D numerical model, developed using the PLAXIS software, was used to conduct the numerical research. The time-dependent behavior of the raft with and without the consideration of micropiles was assessed. Moreover, the variation of load-sharing ratios with time was investigated. The numerical results emphasize that the underpinning process was effective and reduced the final raft rotation and maximum settlement by 79.9% and 73.9%, respectively, compared to the case of the absence of micropiles. The consolidation process under a steady level of vertical loads enhanced the performance of the micropiled and unmicropiled rafts against upcoming lateral loads. The vertical load-sharing ratio increased during a life span of 20 years by 10.4% due to the consolidation process, but the increase was at a decreasing rate. Comparing all the four directions in which the lateral load was applied, the micropiles carried (57.4–76.6%) of the lateral load.

9 January 2018 in Construction Innovation
Verified
Journal Article
Closed access
AAAhmed Atta
Ahmed Atta
NANehal Ali
Nehal Ali
MTMohamed Taman
Mohamed Taman
Emad EtmanEmad Etman
Emad Etman
Purpose: This study aims to investigate the use of CdO nanoparticles with recycled aggregates (RAs) and its effect on the structural behavior of reinforced concrete (RC) slab elements. Design/methodology/approach: The study has been conducted through three phases: in the first phase, the structure of lab-synthesized CdO nanoparticles was investigated and then cement was partially replaced by CdO nanoparticles to estimate the optimum dose. The second phase focused on the properties of the RA collected from demolition wastes. In the third phase, RC slabs with different concrete mixes using RA and CdO nanoparticles were experimentally tested. Findings: The results indicated good effect of using CdO nanoparticles with RA to improve the RC slab specimens’ behavior compared with the control specimen. Originality/value: In present times, nanoparticles have a promising importance in the construction field. The influence of nanoparticles on the compressive strength of the concrete has been investigated by many researchers, but using it with RA is considered a new topic.

1 June 2019 in Journal of Engineering Research
Verified
Journal Article
Open access
PDF file
MGMohamed M. Gaber
Mohamed M. Gaber
Emad EtmanEmad Etman
Emad Etman
HSHaytham M. Sanad
Haytham M. Sanad
Mohamed MarzoukMohamed Marzouk
Mohamed Marzouk
Successful construction projects should meet the planning and design objectives within budget and time constraints. Planning and scheduling for the construction projects and their resources are essential tasks for overall project success. Cash, in particular, is an important resource for construction companies. It is worth noting that while pricing bill of quantities in unit price contracts, the contractor might ignore the related cash flow which may be insufficient for contractor. Further, the resulted financial threats also might be ignored. Therefore, it is important for the contractor to have an overall optimized system to improve all financial aspects related to the contract. This paper presents a cash flow optimization model that aims at maximizing cumulative concurrent investment profit (CCIP) and minimizing maximum monthly overdrafts (OMax). The model utilizes Genetic Algorithms for optimization. The performance of the developed model is validated using an actual case study of "Beni Suef Power Station Project" located in Beni Suef, Egypt.