This study was carried out to evaluate the potential application of pine cone (PC)-derived activated biochar which has a surface area of 1714.5 m2/g for bromocresol green (BCG) dye removal from aqueous solution. Batch adsorption experiments involved varying pH, temperature, contact time, adsorbent dosage, and initial dye concentrations and the maximum BCG removal (96.27%) occurred at pH: 2.0, T: 45 °C, m: 2 g/L, t: 15 min., and Co: 25 mg/L. To study the characteristics of adsorption, the adsorption kinetic isotherm and thermodynamic parameters were employed. The experimental data was evaluated to fit well with the Temkin isotherm (R2 = 0.99) and the adsorption process followed pseudo-first-order kinetics (R2 = 0.96). Thermodynamic parameters obtained from the adsorptive uptake showed that the interaction was endothermic and spontaneous in nature. The regenerated activated PC biochar showed good performance (95.0%), even, after 4th regeneration. To predict the BCG adsorption capacity of activated PC biochar, many different artificial neural network (ANN) models have been developed. The optimal ANN model gave mean absolute error (MAE), mean bias error (MBE), root mean square error (RMSE), and R2 values of 0.036, 0.578, 0.947, and 0.999, respectively. The results obtained showed that ANN can be used to effectively model the BCG adsorption process.
In this study, the optimum hydrothermal conditions of sugar beet pulp were investigated by Response Surface Methodology (RSM) based on Central Composite Design (CCD). The hydrochar obtained from sugar beet pulp (SBP) was optimized for maximum yield and carbon content. Process conditions were chosen with reaction temperatures of 200–240 °C, residence time 60–150 min, and biomass to water ratio of 1:3–1:10. The yield and carbon content of the hydrochar varied with the process parameters. In order to obtain hydrochar with the highest yield and carbon content in optimization, the reaction temperature should be 220.74 °C, the biomass to water ratio should be 1:3, and the residence time should be 95.58 min. High heating value, energy and mass yield, and energy densification ratio of sugar beet pulp and hydrochar were also investigated. The products were characterized using FT-IR, SEM, and ultimate analysis techniques. The Coats-Redfern method was used to estimate the kinetic parameters of the combustion processes. The activation energy values of SBP and SBP-HC products were calculated as 13.88 and 11.46 kJ/mol, respectively. The kinetic data were used to determine the thermodynamic parameters (ΔH, ΔG, and ΔS). As a result, the properties of hydrochar produced from sugar beet pulp under optimum conditions have been extensively investigated and the results have shown that hydrochar has potential for use in different areas.
3 May 2025 in Environment, Development and Sustainability
Managing chicken farming waste is quite difficult due to its potential environmental impacts. To address these issues and promote sustainable poultry farming, effective waste management strategies are essential. In this regard, converting waste into biochar (BC) provides an eco-friendly solution for environmental remediation processes. In this study, chicken manure waste derived biochar was produced within a fixed bed reactor, employing the optimal pyrolysis conditions (440 °C, 7 °C/min, and 115 min) determined through Response Surface Methodology based on Central Composite Design. Subsequently, this solid product underwent activation using two distinct chemical agents (HCl and KOH). Characterized biochar products were investigated for a range of applications, including energy conversion, gas emission control, CO2 capture, and the removal of dyestuff from aqueous solutions-each of which is vital for protecting water resources, reducing pollution, mitigating climate change, and ensuring compliance with environmental regulations. The CO2 adsorption capacities of Raw-BC, KOH-BC and HCl-BC products were measured as 27.52, 66.62 and 51.26 mg/g at 25 °C, respectively. The highest CO2 adsorption capacity of 1.51 mmol/g was achieved with KOH-BC. The Raw-BC had the highest methylene blue removal rate (80%) at 45 °C, pH 4–5, for up to 300 min. When the fuel properties of the raw biochar were compared with different types of coal, it was concluded that this product could be used instead of lignite coal in energy production. As a result, this multifaceted approach showcased the versatility and potential benefits of biochar in diverse environmental and industrial applications.
23 March 2023 in Biomass Conversion and Biorefinery
In this study, hydrochar products were obtained from kidney bean shell (KBS) biomass at different temperatures using the hydrothermal carbonization (HTC) method. Hydrochar products were produced at three different temperatures (200, 220 and 240 C) and a holding time of 90 minutes. Biomass/water ratio was taken as 1:10. Analysis techniques such as Thermogravimetric analysis (TG), Ultimate analysis and Fourier Transform Infrared Spectroscopy (FTIR) were used in the characterization of raw materials and hydrochar products. In addition, the fuel properties (high heating value, energy yield and energy densification ratio) of raw KBS and hydrochar products were also investigated. As the HTC temperature increases, the high heating value of hydrochar products increases. Among hydrochar products, the highest high heating value belongs to the product obtained at 240 C. The combustion behavior of raw and hydrochar a product was examined using the thermogravimetric analysis method and combustion parameters (Ti, Tb and Tm) were determined. As a result, this study has shown that the hydrochar product produced from KBS by hydrothermal carbonization method can be used as a biofuel material.