Aluminium alloys are widely used in many industries due to their high strength-to-weight ratios and resistance to corrosion. Due to their specific thermophysical properties and intricate physical metallurgy, these alloys are challenging to weld. Work-hardened alloys may experience strength loss in heat-affected zones (HAZ). The strength of precipitation-hardened alloys is severely damaged in both HAZ and weld metal due to coarsening or full dissolution. The high thermal conductivity and reflectivity of aluminium causes lower laser beam absorptivity with lower processing efficiency. Weld imperfections such as porosity, humping, and underfills are frequently formed due to the low melting point and density promoting high liquidity with low surface tension. Porosity is the most persistent imperfection and is detrimental for mechanical properties. In this work, extensive review was made on laser beam and laser-arc hybrid welding of aluminium alloys. Solidification cracking, evaporation of alloying elements, porosity and keyhole stability, and other challenges are studied in detail. The current development of laser welding of aluminium alloys is not so mature and new discoveries will be made in the future including the use of newly developed laser systems, welding consumables, welding methods, and approaches.

For many years, the oil and gas industry has utilized superduplex stainless steels due to their high strength and excellent corrosion resistance. Wire arc additive manufacturing (WAAM) was used with superduplex filler wire to create walls with different heat input. Due to the multiple heating and cooling cycles during layer deposition, brittle secondary phases may form such as intermetallic sigma (σ) phase. By inspecting deposited walls within wide range of heat inputs (0.40–0.87 kJ/mm), no intermetallic phases formed due to low inter-pass temperatures used, together with the high Ni content in the applied wire. Lower mechanical properties were observed with high heat inputs due to low ferrite volume fraction, precipitation of Cr nitrides and formation of secondary austenite. The walls showed good toughness values based on both Charpy V-notch and CTOD (crack tip opening displacement) testing.

Superduplex stainless steels have been used in the oil and gas industry for a couple of decades due to the combination of excellent mechanical properties and corrosion resistance. The present investigation addresses the applicability of wire and arc additive manufacturing for this steel grade. Due to the inherent rapid heating and cooling, the initial base metal microstructure will be substantially altered, and complex thermal cycles may cause the formation of brittle secondary phases, among which the frequently observed intermetallic sigma phase is most harmful. However, no intermetallic phases have been observed, which is consistent with the low heat input employed, and the high Ni content in the wire. The microstructure observations in terms of ferrite volume fraction, Cr nitrides precipitation and the formation of secondary austenite are discussed together with the hardness measurements, tensile testing and notch toughness testing. It is concluded that additive manufacturing of superduplex stainless steels by wire and arc process is feasible.

Modern industry requires different advanced metallic alloys with specific properties since conventional steels cannot cover all requirements. Aluminium alloys are becoming more popular, due to their low weight, high corrosion resistance, and relatively high strength. They possess respectable electrical conductivity, and their application extends to the energy sector. There is a high demand in joining aluminium alloys with other metals, such as steels, copper, and titanium. The joining of two or more metals is challenging, due to formation of the intermetallic compound (IMC) layer with excessive brittleness. High differences in the thermophysical properties cause distortions, cracking, improper dilution, and numerous weld imperfections, having an adverse effect on strength. Laser beam as a high concentration energy source is an alternative welding method for highly conductive metals, with significant improvement in productivity, compared to conventional joining processes. It may provide lower heat input and reduce the thickness of the IMC layer. The laser beam can be combined with arc-forming hybrid processes for wider control over thermal cycle. Apart from the IMC layer thickness, there are many other factors that have a strong effect on the weld integrity; their optimisation and innovation is a key to successfully delivering high-quality joints.

Aluminium alloys processed by wire arc additive manufacturing (WAAM) exhibit a relatively coarse microstructure with a columnar morphology. A powerful measure to refine the microstructure and to enhance mechanical properties is to promote grain refinement during solidification. Addition of ceramic nanoparticles has shown great potential as grain refiner and strengthening phase in aluminium alloys. Thus, an Al-Mg alloy mixed with TiC nanoparticles was manufactured by the novel metal screw extrusion method to a wire and subsequently deposited by WAAM. Measures to restrict oxidation of magnesium during metal screw extrusion were examined. Purging of CO₂ gas into the extrusion chamber resulted in a remarkable reduction in formation of MgO and Mg(OH)₂. TiC decomposed to Al₃Ti during WAAM deposition, leading to a significant grain refinement of 93% compared to a commercial benchmark. The presence of remaining TiC nanoparticles accounted for an increased hardness of the WAAM material through thermal expansion mismatch strengthening and Orowan strengthening. Exposure of TiC to moisture in air during metal screw extrusion increased the internal hydrogen content significantly, and a highly porous structure was seen after WAAM deposition.

Aluminum and its alloys are widely used in various applications including e-mobility applications due to their lightweight nature, high corrosion resistance, good electrical conductivity, and excellent processability such as extrusion and forming. However, aluminum and its alloys are difficult to process with a laser beam due to their high thermal conductivity and reflectivity. In this article, the two most used laser processes, i.e., laser welding and laser powder bed fusion (LPBF) additive manufacturing, for processing of aluminum have been studied. There are many common laser-material interaction mechanisms and challenges between the two processes. Deep keyhole mode is a preferred method for welding due to improved productivity, while a heat conduction mode is preferred in LPBF aiming for zero-defect parts. In LPBF, the processing maps are highly desirable to be constructed, which shows the transition zone. Presented numerical modeling provides a more in-depth understanding of porosity formation, and different laser beam movement paths have been tested including circular oscillation paths. High accuracy processing maps can be constructed for LPBF that allows us to minimize tedious and time-consuming experiments. As a result, a modeling framework is a highly viable option for the cost-efficient optimization of process parameters.