MOHAMMED EL HALAOUI

Mr. MOHAMMED EL HALAOUI

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 December 2025
Verified
Conference Paper
Closed access
MOHAMMED EL HALAOUIMOHAMMED EL HALAOUI
MOHAMMED EL HALAOUI
MHMustapha El Halaoui
Mustapha El Halaoui
LALahcen Amhaimar
Lahcen Amhaimar
AAAdel Asselman
Adel Asselman
Bousselham SamoudiBousselham Samoudi
Bousselham Samoudi
Laurent CanaleLaurent Canale
Laurent Canale

12 November 2024
Verified
Conference Paper
Closed access
MOHAMMED EL HALAOUIMOHAMMED EL HALAOUI
MOHAMMED EL HALAOUI
MHMustapha El Halaoui
Mustapha El Halaoui
LALahcen Amhaimar
Lahcen Amhaimar
Laurent CanaleLaurent Canale
Laurent Canale
BSBousselham Samoudi
Bousselham Samoudi
Optimizing the performance of organic light-emitting diodes (OLEDs) containing a dopant in the emissive layer (EML), requires the coupling of electrical and optical simulations to design device structures before proceeding to fabrication. Electrical or optical simulation alone, is not sufficient to properly optimize an OLED structure. By adjusting the conditions at the interlayer interfaces, taking into account defect states in the organic layers and controlling the thickness of the doped emissive layer in the ITO/NPB/Alq3(1%)/Alq3/LiF/Al structure, the performance of five different devices with different emissive layer thicknesses (15, 30, 45, 60, and 75 nm) has been studied. Structure characteristics analyzed included current density-voltage relationships, luminance-current density, position-recombination rate and electroluminescence spectrum. According to the results obtained, increasing the thickness of the emissive layer (EML) leads to a decrease in current density and turn-on voltage, affects the recombination rate and, consequently, the luminance and light spectrum, while the device with 30 nm thick EML has a clearer and higher maximum emission intensity than the other devices.

19 May 2026 in Electronics
Verified
Journal Article
Open access
PDF file
MOHAMMED EL HALAOUIMOHAMMED EL HALAOUI
MOHAMMED EL HALAOUI
MHMustapha El Halaoui
Mustapha El Halaoui
ALAmhaimar Lahcen
Amhaimar Lahcen
AAAdel Asselman
Adel Asselman
Laurent CanaleLaurent Canale
Laurent Canale
Bousselham SamoudiBousselham Samoudi
Bousselham Samoudi
In scientific research, the optimization of organic light-emitting diodes (OLEDs) is generally achieved through a lengthy and expensive experimental process as new ideas and configurations are tested on real devices. Electro-optical simulation allows for the rapid evaluation of key performance parameters of device structures, thus reducing manufacturing time and costs. This paper presents an original contribution to the electro-optical modeling and optimization of multilayer OLED devices using the Non-dominated Sorting Genetic Algorithm II (NSGA-II). This optimization explicitly incorporates defect states within the ITO/NPB/Alq3:C545T/Alq3/LiF-Al structure. The simulated model is calibrated using experimental data by fitting the trap state distribution. The Pareto front resulting from the multi-objective optimization identifies a set of non-dominated configurations, including an optimal intermediate structure defined by an electron transport layer (ETL) thickness of approximately 42 nm and a hole transport layer (HTL) thickness of approximately 53 nm. This configuration leads to a limited reduction of 1.75–2% in current efficiency (ηc) while offering a remarkable improvement of 23–30% in power efficiency (ηp) compared to the extreme configurations of the optimal Pareto set. Thus, this solution represents an optimal Pareto trade-off between high current efficiency and improved power efficiency. This paper shows that combining defect modeling and thickness optimization provides a reliable framework for the electro-optical optimization of OLED devices. Future work will extend this approach to spectral and colorimetric analysis.
2

15 September 2026 in Electronics
Verified
Journal Article
Open access
PDF file
MOHAMMED EL HALAOUIMOHAMMED EL HALAOUI
MOHAMMED EL HALAOUI
MHMustapha El Halaoui
Mustapha El Halaoui
ISIbrahim Saadouni
Ibrahim Saadouni
ALAmhaimar Lahcen
Amhaimar Lahcen
AAAdel Asselman
Adel Asselman
Bousselham SamoudiBousselham Samoudi
Bousselham Samoudi
This article presents a multi-objective optimization framework for fluorescent organic light-emitting diodes (OLEDs), combining numerical simulation with an analysis of exciton populations and the associated loss mechanisms. An ITO/NPB/Alq3:C545T/Alq3/LiF–Al structure was modeled, calibrated, and validated against experimental electro-optical characteristics. The influence of the emissive layer thickness (tEML) and the C545T doping concentration (Dp) was systematically studied across 25 configurations, with tEML= 20–40 nm and Dp=1–9%, under two operating conditions: J=0.15 A/cm2 and L=5000 cd/m2. Increasing the dopant concentration led to a marked deterioration in current efficiency (ηc) and power efficiency (ηp), together with a progressive localization of singlet excitons near the interface between the emissive layer (EML) and the hole transport layer (HTL) in structures with thinner EMLs. This exciton localization was accompanied by an increased contribution from non-radiative deactivation pathways, which were incorporated into a dopant singlet-exciton loss fraction, Floss,d. The systematic increase in this loss fraction with increasing dopant concentration and its overall inverse relationship with ηc and ηp motivated the development of a three-objective formulation that maximizes ηc and ηp while minimizing Floss,d. The Non-dominated Sorting Genetic Algorithm II (NSGA-II) identified compromise solutions at the lowest dopant concentration, Dp=1%, with tEML=24–25 nm under both operating conditions. Multi-objective Particle Swarm Optimization (MOPSO) identified a trade-off region comparable to that obtained by NSGA-II, providing a cross-algorithm consistency check of the reported numerical results. The proposed methodology thus establishes a physically grounded link between device design, the spatial redistribution of excitons, the modeled loss pathways, and the macroscopic performance of OLEDs, thereby providing an interpretable framework for the multi-objective optimization of fluorescent OLEDs prior to fabrication.