Several efforts have been dedicated to the development of lignin-based polyurethanes (PU) in recent years. The low and heterogeneous reactivity of lignin hydroxyl groups towards diisocyanates, arising from their highly complex chemical structure, limits the application of this biopolymer in PU synthesis. Besides the well-known differences in the reactivity of aliphatic and aromatic hydroxyl groups, experimental work in which the reactivity of both types of hydroxyl, especially the aromatic ones present in syringyl (S-unit), guaiacyl (G-unit), and p-hydroxyphenyl (H-unit) building units are considered and compared, is still lacking in the literature. In this work, the hydroxyl reactivity of two kraft lignin grades towards 4,4′-diphenylmethane diisocyanate (MDI) was investigated. ³¹P NMR allowed the monitoring of the reactivity of each hydroxyl group in the lignin structure. FTIR spectra revealed the evolution of peaks related to hydroxyl consumption and urethane formation. These results might support new PU developments, including the use of unmodified lignin and the synthesis of MDI-functionalized biopolymers or prepolymers.

Owing to its chemical structure, wide availability and renewable nature, lignin is a promising candidate for the partial replacement of fossil-based raw material in the synthesis of epoxy resins. Its poor compatibility has been reported to be one of the main drawbacks in this domain. On the other hand, a well-established modification method for lignin epoxidation has been used for many years for the improvement of lignin compatibility. However, the extent of the effect of lignin epoxidation on the improvement of bio-based epoxy mechanical properties, applied as adhesives, is still an open question in the literature. In this context, a pristine and industrial grade kraft lignin (AKL) was reacted with epichlorohydrin to yield epoxidized lignin (E-AKL) in this work. Afterwards, AKL or E-AKL were separately blended with petroleum-based epoxy resin at 15 and 30 wt% and cured with a commercial amine. The adhesive curing kinetic was evaluated using a novel technique for thermal transition characterization, Temperature Modulated Optical Refractometry (TMOR); the results showed that the incorporation of AKL reduces the crosslinking rate, and that this effect is overcome by lignin modification. Mechanical tests revealed an improvement of impact and practical adhesion strength for samples containing 15 wt% of E-AKL. These results elucidate the effect of lignin epoxidation on the application of lignin-based epoxy adhesives, and might support the further development and application of these bio-based materials.

This work aimed to evaluate the influence of the aliphatic and aromatic hydroxyl level on the polyurethane adhesive property and chemical structure. This adhesive was obtained through the reaction of technical Kraft lignin (TKL) as polyol with diphenylmethane diisocyanate (MDI). Thus, lignopolyurethane adhesives were obtained with NCO:OH ratios of 0.8:1.0, 0.9:1.0, 1.0:1.0, 1.1:1.0, and 1.2:1.0. Initially only the TKL aliphatic hydroxyl level was taken into consideration in the stoichiometry in order to define the mass ratio between MDI and polyol. Subsequently, lignopolyurethane adhesive was obtained using the same NCO:OH ratios considering TKL total hydroxyls’ level, and aromatic and aliphatic hydroxyls. The chemical structures of the synthesized adhesives were analyzed by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (¹³C NMR). The mechanical property of the adhesively bonded joints, comprising wood substrates and synthesized adhesives, was measured using single lap shear tests. Results illustrated that by increasing the NCO:OH ratio, there is an increase in the free isocyanate content leading to higher shear strength values. Higher free isocyanate content leads to MDI dimer formation in the lignopolyurethane structure.

New techniques to manipulate the electronic properties of few layer 2D materials, unveiling new physical phenomena as well as possibilities for new device applications have brought renewed interest to these systems. Therefore, the quest for reproducible methods for the large scale synthesis, as well as the manipulation, characterization and deeper understanding of these structures is a very active field of research. We here report the production of nitrogen doped bilayer graphene in a fast single step (2.5 minutes), at reduced temperatures (760 °C) using microwave plasma-enhanced chemical vapor deposition (MW-PECVD). Raman spectroscopy confirmed that nitrogen-doped bilayer structures were produced by this method. XPS analysis showed that we achieved control of the concentration of nitrogen dopants incorporated into the final samples. We have performed state of the art parameter-free simulations to investigate the cause of an unexpected splitting of the XPS signal as the concentration of nitrogen defects increased. We show that this splitting is due to the formation of interlayer bonds mediated by nitrogen defects on the layers of the material. The occurrence of these bonds may result in very specific electronic and mechanical properties of the bilayer structures.

In 2021, global petroleum-based plastic production reached over 400 million metric tons (Mt), and the accumulation of these non-biodegradable plastics in the environment is a worldwide concern. Polyhydroxybutyrate (PHB) offers many advantages over traditional petroleum-based plastics, being biobased, completely biodegradable, and non-toxic. However, its production and use are still challenging due to its low deformation capacity and narrow processing window. In this work, two linear-chain polyester oligomers were used as plasticizers to improve the processability and properties of PHB. Thermal analyses, XRD, and polarized optical microscopy were performed to evaluate the plasticizing effect on the PHB and the reflection on the mechanical behavior. Both oligomers acted as PHB plasticizers, with a reduction in T_g and T_m as a function of the plasticizer concentration, which can make it easier to handle the material in thermal processing and reduce the probability of thermal degradation. Plasticizer 2 proved to be the most promising between the two with an optimized condition of 20%, in which there was a decrease in elastic modulus of up to 72% and an increase in the maximum elongation of 467%.