This work presents a comprehensive literature review of the coefficient of linear thermal expansion (CLTE) of polymers and polymer composite materials (PCMs). It systematizes CLTE measurement methods for isotropic and anisotropic materials, including contact techniques such as dilatometry and thermomechanical analysis and non-contact methods such as digital image correlation, laser interferometry, diffraction-based techniques, and strain-gauge methods, with attention to their accuracy and fields of applicability. Furthermore, the review describes the principal mathemaical modeling approaches used to predict the CLTE of polymers and PCMs. The review also provides a comparative analysis of CLTE values for a broad range of thermoplastics (commodity, engineering, and high-performance grades) and thermosets, identifying the key factors that govern CLTE, such as the transition from the glassy to the viscous-flow state, the presence and anisotropy of a crystalline phase, and related structure–property effects. Special consideration is given to the factors determining the CLTE of polymer composites, including the properties of the polymer matrix, the nature, size, orientation and surface treatment of the filler, the architecture and reinforcement scheme of the composite, and the manufacturing process. The review also outlines application areas in which PCMs with controlled or reduced CLTE are required and illustrates these with specific examples. Thus, the article provides integrated view of the CLTE of polymers and PCMs, compiles reference data for CLTE values of various polymers and common composite fillers and offers practical recommendations for selecting polymer materials for fabricating goods that require high thermal dimensional stability.
Background/Objectives: Residues of β-lactam antibiotics in foods of animal origin are important for official residue control and public-health risk assessment. Sample storage conditions may affect the measured concentrations of these analytes, whereas cooking may influence consumer exposure. This study evaluated the stability of six β-lactam antibiotics—amoxicillin, ampicillin, phenoxymethylpenicillin, benzylpenicillin, cefazolin, and cefotaxime—and clavulanic acid, a β-lactamase inhibitor, in chicken meat during storage and thermal processing. Methods: Incurred chicken meat samples were obtained after in vivo administration of the studied compounds. Stability was assessed during storage at +4 °C, −20 °C, and −86 °C for up to 165 days, during repeated freeze–thaw handling, and during heating at 100 °C for up to 30 min. The target compounds were quantified by HPLC–MS/MS after acetonitrile extraction and hexane clean-up. Results: The studied compounds were unstable at +4 °C, with concentrations decreasing below the detection limit within 3–27 days depending on the compound. Storage at −20 °C was insufficient for long-term preservation of most penicillins, whereas −86 °C improved stability. Cefazolin was the most stable compound under the tested storage conditions, while cefotaxime was the least stable. Heating at 100 °C for 30 min caused substantial reduction in parent-compound concentrations, ranging from 63.8 ± 4.0% for cefazolin to complete disappearance below the detection limit for cefotaxime. Conclusions: For reliable official residue analysis, chicken meat samples intended for β-lactam testing should be stored at −86 °C whenever long-term storage is required. Repeated thawing should be avoided. Cooking substantially reduces the concentrations of the parent compounds but cannot be considered a reliable safety measure, because degradation may be incomplete and degradation products were not assessed in this study.
The use of lunar regolith (LR) for lunar construction is a key route to reducing the mass of materials transported from Earth. In this work, highly filled composites based on polyphenylsulfone (PPSU) with Tg = 219.1 °C and modified polyetherimide (PEI) with Tg = 247.1 °C containing up to 92.5 wt.% of LR simulant were prepared by dry blending the LR simulant and the polymer powders, followed by hot pressing. Their internal structure, mechanical, thermal, thermomechanical, and melt/flow properties were evaluated. The properties of the composites strongly depended on the LR simulant content and were governed by two competing mechanisms: restriction of polymer-chain mobility and of matrix deformation by the rigid mineral filler at moderate LR simulant contents, and increased porosity and loss of matrix continuity caused by binder deficiency at excessive filler loadings. At LR simulant contents of up to 60 wt.% for PPSU and 85 wt.% for PEI, dense, low-porosity (<10 vol.%) monolithic composites were formed, whereas higher filler loadings led to binder deficiency and increased porosity. LR simulant incorporation increased Shore D hardness from 75 to 88 for PPSU- and from 86 to 96 for PEI-based composites. Maximum compressive strength/modulus reached 122 MPa/6.3 GPa for PPSU- and 193 MPa/7.4 GPa for PEI-based composites, compared with 93 MPa/2.3 GPa and 150 MPa/3.3 GPa for neat polymers, respectively. Thermal conductivity increased to 0.64 and 0.72 W/(m·K), while CLTE decreased to 14.2 × 10−6 K−1 and 10.1 × 10−6 K−1 for PPSU- and PEI-based composites, respectively. Composites containing 50–60 wt.% of LR simulant retained melt/flow capability, indicating their potential suitability for processing by melt extrusion and additive manufacturing. Based on the obtained data, recommendations were formulated for application of the developed composites in melt-based 3D printing of complex-geometry parts and hot-pressed simple-shape construction elements.
A simplified and efficient sample preparation method combined with high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) has been developed for the determination of twelve aminoglycoside antibiotic pesticides: amikacin, apramycin, validamycin, gentamicin, hygromycin, dihydrostreptomycin, kanamycin, kasugamycin, neomycin, paromomycin, streptomycin, and zhongshengmycin in matrices with high starch content (rice), high acidity (lemon), high fat content (avocado), and high water content (cucumber). The method involves extraction of the compounds with a specific buffer solution consisting of ammonium acetate, EDTA, sodium chloride, and trichloroacetic acid, followed by the extraction of the analytes from the extracts using HLB cartridges. Validation results were satisfactory: the correlation coefficients for the calibration curves (R²) exceeded 0.99 for all target compounds within the linear range across four matrices. Limits of detection (LOD) were 3–15 μg/kg, and limits of quantification (LOQ) were 10–50 μg/kg. Inter-day and intra-day relative standard deviations (RSD) did not exceed 20 %.
23 September 2026 in Inorganic Materials: Applied Research
The work reports the synthesis and study of thermal, mechanical and processing properties of copolyetherimides that contain rigid-chain segments of commercially available dianhydrides. It is shown that incorporating rigid segments into the macromolecular chains increases the glass transition temperature and the thermo-oxidative stability of the polymers, but is accompanied by a decrease in melt flow and a partial deterioration of mechanical properties. As a result of analyzing the experimental data, a composition with an optimal overall balance of properties was identified; it exhibits heat resistance 15–20°C higher than the original unmodified polyetherimide while retaining mechanical properties and a melt flow index at an acceptable level. A key outcome of this work is the successful extrusion processing of the developed copolyetherimide into pellets without significant thermo-oxidative degradation, thereby preserving its mechanical properties. The obtained data confirm the prospects of a method of copolymerization with rigid-chain dianhydrides for creating structural polyetherimides with an extended temperature range and indicate the broad application potential of the developed materials.