An SGI was machined into 400 g cylindrical pieces and remelted in an electrical resistance furnace protected by Ar gas to produce materials ranging from SGI to CGI. The graphite morphology was controlled by varying the holding time at 1723 K (1450 °C) between 10 and 60 minutes. The discrete sectional size distribution of nodules by number density was measured on cross sections of the specimens and translated to volumetric distribution by volume fraction. Subpopulations of nodules were distinguished by fitting Gaussian distribution functions to the measured distribution. Primary and eutectic graphite, were found to account for most of the volume of nodular graphite in all cases. For holding times of 40 minutes and greater, corresponding to nodularity roughly below 40 pct, the primary subpopulation was very small and difficult to distinguish, leaving eutectic nodules as the dominant subpopulation. The mode and standard deviation of the two subpopulations were roughly independent of nodularity. Moreover, the nodular and vermicular graphite were segregated in the microstructure. In conclusion, the results suggest that the parallel development of the vermicular eutectic had small influence on the size distribution of eutectic graphite nodules.
13 February 2020 in International Journal of Metalcasting
Spheroidal graphite is the defining microstructural feature of ductile iron and also plays an important role in compacted graphite iron. It is widely accepted that graphite spheroids are engulfed by austenite at an early stage of solidification after which their growth is impeded by the slow diffusion of carbon through a layer of austenite. In this work, a compacted graphite iron-containing spheroidal graphite was studied after interruption of its solidification by water quenching. Selected areas of a cross section of the castings were investigated using quantitative electron probe microanalysis, with emphasis on the distribution of carbon in austenite. The measured carbon concentration near graphite was generally below the theoretical carbon concentration in austenite at equilibrium with graphite at 1140 °C. Numerical simulations of diffusion of carbon in austenite around spheroidal graphite suggest that a zone of austenite around graphite was likely depleted of carbon during quenching, possibly explaining the low measured concentrations. The measured carbon concentration near graphite varied by as much as 0.3 wt%, with the lowest concentrations consistently found in the central region of compacted graphite–austenite eutectic cells. Regardless of whether these differences were present prior to quenching or are consequences thereof, they seem to reflect either departures from, or displacements of, the carbon concentration in austenite at equilibrium with graphite. This indicates that there is something about growth of graphite embedded in austenite which is not well understood. Concentrations of Si, Mn and Cu are near equal in the compared regions and do not explain the observed differences in carbon content near graphite.
17 January 2024 in International Journal of Metalcasting
Solidification of cast irons usually involves dendritic growth of austenite. This article presents a literature survey about the dendrites in cast irons, their consequences and how they may be manipulated. The literature review is supplemented with relevant micrographs from our research. While austenite usually transforms into ferrite or pearlite, the dendrites limit where liquid flows, where eutectic grows, and where segregated elements go. The amount and shape of dendrites show correlations with tensile strength in pearlitic gray and compacted graphite irons. There are also indications that a coarse dendrite grain structure may be beneficial to tensile strength. The dendrite grain structure depends on melting process parameters and shows sensitivity to melt treatment. The evolution of scale of dendrite arms and their spacing under isothermal condition is by now fairly well-understood; however, work remains to better understand its evolution during cooling and its interaction with the eutectic. The amount and shape of dendrites are less understood in irons of near-eutectic and hypereutectic composition, in particular mixtures of dendrites of distinct scales, associated with regions of distinct graphite morphology. While significant advances have been made in recent years, the role and control of dendrites remain a relatively unexplored area of research with potential to improve production and properties of cast irons.
26 September 2023 in International Journal of Metalcasting
Porosity is the culprit for a large fraction of scrap in cast iron foundries, resulting in significant environmental and productivity losses. The present work focuses on characterizing and explaining porosity defects in industrial compacted and nodular graphite cast iron components, utilizing current literature for reference. The goal is to identify existing knowledge gaps in the field, fostering further research work. Complex-shaped castings were sampled from three foundries, weighing between 100 and 300 kg. These were carefully selected to capture recurring defects during stable production. The mechanisms behind these defects were discussed, and the findings were compared to the literature. Scanning electron microscopy (SEM) was used to investigate the inner surfaces of the pores with secondary electron imaging. The surrounding microstructure was captured with optical microscopy in combination with image analysis, where panoramic images and nodularity maps were built. Ultimately, etching based on Si segregation was employed. The results suggest that the understanding of pore surface film formation remains limited, particularly regarding graphite film formation. Notably, the observations reveal a multitude of previously unreported graphite structures within the pores, some with particles in their centers containing Ce, Ca, La and S. These novel structures can provide additional insights regarding pore formation chronology.
8 December 2015 in Metallography, Microstructure, and Analysis
This paper describes and validates a methodology for implementation of full-scale sand-casting simulation in a general-purpose finite element software, including mold filling, heat transport, solidification kinetics, chemical microsegregation and prediction of microstructure and material properties. The solidification model, customized for gray cast iron, includes novel methods for handling interaction between parallel dendritic and eutectic solidification modes and its impact of their interaction on the final microstructure. The validation involves a previously published gray iron casting experiment and involves comparison of simulated and experimental cooling curves, microstructure parameters and tensile strength. We believe that this is valuable to researchers and engineers seeking to improve the state of the art of casting simulation tools.