Yaşar AYAZ

Dr. Yaşar AYAZ

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2015 in Construction and Building Materials
Verified
Journal Article
Closed access
YAYaşar AYAZ
Yaşar AYAZ
AKAdnan Fatih Kocamaz
Adnan Fatih Kocamaz
MKMehmet Burhan Karakoç
Mehmet Burhan Karakoç

1 June 2017 in International Journal of Adhesion and Adhesives
Verified
Journal Article
Closed access
ŞÇŞ. Çitil
Ş. Çitil
YAYaşar AYAZ
Yaşar AYAZ
ŞTŞ. Temiz
Ş. Temiz
AYAydın
Aydın

12 August 2015 in The Journal of Adhesion
Verified
Journal Article
Closed access
ŞÇŞerif Çitil
Şerif Çitil
YAYaşar AYAZ
Yaşar AYAZ
ŞTŞemsettin Temiz
Şemsettin Temiz
Accidents in the industry, especially in the field of aerospace, are quite common. Damages like tears cracks and holes occur especially when small sand particles present in the airfield collide with the body and wings of an airplane during takeoff and landing. This torn, cracked, or pierced region should be repaired gently. Damaged parts are frequently small regions for which repair is more suitable than complete replacement as workmanship; cost and time are an important concept in today’s world. A gap occurs between the patches if double-bonded patches are used in the repair of the damaged parts. In this study, the region between patches in a joint with and without intermediate parts was modeled and its effect on strength was examined numerically and experimentally. The effects of patch thickness, overlap length, adherent thickness, and gap length on the strength of the joints with and without intermediate part was compared. The results show that the intermediate part does not have any influence on the strength of the lap joint such that double strap joints without intermediate part have higher failure load. Additionally, it is seen that the failure load decreased with increasing patch thickness and increased with the thickness of the adherent.

17 May 2016 in Materialwissenschaft und Werkstofftechnik
Verified
Journal Article
Closed access
PDF file
YAYaşar AYAZ
Yaşar AYAZ
ŞÇŞ. Çitil
Ş. Çitil
MSMehmet fatih Sahan
Mehmet fatih Sahan

2 June 2020 in Structural Concrete
Verified
Journal Article
Closed access
PDF file
AKAdnan Fatih Kocamaz
Adnan Fatih Kocamaz
YAYaşar AYAZ
Yaşar AYAZ
MKMehmet Burhan Karakoç
Mehmet Burhan Karakoç
ITİbRahim Türkmen
İbRahim Türkmen
RDRamazan Demirboğa
Ramazan Demirboğa

1 July 2021 in Materials Testing
Verified
Journal Article
Closed access
YAYaşar AYAZ
Yaşar AYAZ
ÇŞÇitil Şerif
Çitil Şerif
Factors such as the surface geometry of a joint, the direction of the applied load, and the type of adhesive used have a great influence on the strength of a joint in adhesive bonding. In adhesively bonded joints (ABJ), it is possible to improve surface geometry by forming various geometric surfaces. ABJs are not very resistant to peeling stress, thus requiring that a bonding model be analyzed according to the direction of the applied load to prevent peeling stress. In this study, a butt curved joint was prepared from aluminum plates (A2024-T3) to improve the surface geometry of the joint. The mechanical behavior of the joints in three-dimensions and subjected to bending were investigated depending on an increase in the curvature radius. The adhesive DP810 was used for bonding. The finite element analysis was performed in ANSYS and cohesive zone modeling was used for a simulation of the damage growth in the adhesive layer. The results of bilinear and exponential models were found to be more appropriate to the experimental results. When the radius of curvature increases, the damage load carried decreases in the butt curved lap joints. It was seen that decreases in the curvature radius significantly decrease normal stress.