In this study approaches for chemical conversions of the renewable compounds 1,2-propanediol (1,2-PD) and 2,3-butanediol (2,3-BD) that yield the corresponding cyclic ketals and glycol ethers have been investigated experimentally. The characterization of the obtained products as potential green solvents and gasoline components is discussed. Cyclic ketals have been obtained by the direct reaction of the diols with lower aliphatic ketones (1,2-PD + acetone → 2,2,4-trimethyl-1,3-dioxolane (TMD) and 2,3-BD + butanone-2 → 2-ethyl-2,4,5-trimethyl-1,3-dioxolane (ETMD)), for which the ΔH⁰_r, ΔS⁰_r and ΔG⁰_r values have been estimated experimentally. The monoethers of diols could be obtained through either hydrogenolysis of the pure ketals or from the ketone and the diol via reductive alkylation. In the both reactions, the cyclic ketals (TMD and ETMD) have been hydrogenated in nearly quantitative yields to the corresponding isopropoxypropanols (IPP) and 3-sec-butoxy-2-butanol (SBB) under mild conditions (T = 120–140 °C, p(H₂) = 40 bar) with high selectivity (>93%). Four products (TMD, ETMD, IPP and SBB) have been characterized as far as their physical properties are concerned (density, melting/boiling points, viscosity, calorific value, evaporation rate, Antoine equation coefficients), as well as their solvent ones (Kamlet-Taft solvatochromic parameters, miscibility, and polymer solubilization). In the investigation of gasoline blending properties, TMD, ETMD, IPP and SBB have shown remarkable antiknock performance with blending antiknock indices of 95.2, 92.7, 99.2 and 99.7 points, respectively.

The nickel–tungsten sulfide catalysts for the hydroconversion of hydrocarbons were prepared from oil-soluble nickel and tungsten precursor compounds in situ with the use of silica, alumina, titania, zeolite Y, and amorphous aluminosilicate as additives in a vacuum gas oil medium. It was found that the catalytic activity in hydrocracking depends on the concentration of acid sites in the resulting catalyst. With the use of oxide additives, the dispersion and the promoter ratio of the in situ formed sulfide particles increased in the order SiO₂–Al₂O₃–TiO₂. It was noted that the promoter ratio of sulfide particles obtained with the use of aluminosilicate additives depended on their porous structure peculiarities. The use of titanium dioxide as a catalytic system component made it possible to reach high activity in hydrocracking, hydrodearomatization, and hydrodesulfurization, which was comparable to that of a system based on zeolite Y, a highly acidic component.

The hydrocracking reaction of a pyrolysis fuel oil fraction using in situ generated nano-sized NiWS-sulfide catalysts is studied. The obtained catalysts were defined using X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). The features of catalytically active phase generation, as well as its structure and morphology were considered. The catalytic reactivity of in situ generated catalysts was evaluated using the hydrocracking reaction of pyrolysis fuel oil to obtain a light fraction to be used as a feedstock for benzene, toluene, and xylene (BTX) production. It was demonstrated that the temperature of 380 °C, pressure of 5 MPa, and catalyst-to-feedstock ratio of 4% provide for a target fraction (IPB −180 °C) yield of 44 wt %, and the BTX yield of reaching 15 wt %.

A cobalt-molybdenum-containing sulfonium thiosalt is prepared; when decomposed in situ, it forms the catalyst active in hydrogenation and hydrodesulfurization. The possibility of catalyst...

The study investigates the activity of an in situ nanosized NiMoS catalyst in the hydrodeoxygenation of diphenyl ether. The hydrodeoxygenation product was found to primarily contain benzene, cyclohexane, and n-hexane. The study identified the effects of reaction temperature and reaction mixture composition on the conversion rate and on the quantitative composition of the product. The conversion rate reached 100% at a substrate : Mo molar ratio of 10.5 : 1. The catalysts isolated after the reaction were analyzed by transmission electron microscopy and X-ray photoelectron spectroscopy. The catalyst dispersion was 1.1.

The effect of precursor on the properties of nanosized sulfide catalysts prepared by the in situ decomposition of nickel–tungsten compounds is studied. Precursors are nickel-thiotungsten...