This paper questions if engineering educators are producing engineers that are accelerating humanity along an unsustainable path. Even though technology and engineering are important drivers in trying to move humanity towards an environmentally sustainable paradigm, the paper suggests that maybe the most important levers and challenges lie in the economic and social domains. Short case studies of energy efficiency, the experience of the industrialist Ray Anderson and the authors own reflection of teaching chemical engineering students are used to highlight this. Engineering/technological innovation may not be enough and is often counteracted by the rebound effect and the current dominant neoclassical economic paradigm. The paper discusses what engineering educators can do to produce sustainability informed engineers who are better able to engage with the economic and social dimensions of sustainability. Some suggestions for engaging engineering students with the economic and social dimensions of environmental sustainability are provided. Engineers must somehow find ways, not just to influence technological levers (which are very important) but also to influence economic and social levers so that changes in economic and social behaviours can complement and facilitate technological change in moving humanity to an environmentally sustainable paradigm.
This work reports on the flowability of novel milk powders that have potential for application in the manufacture of chocolate. Many milk powders are cohesive which can give rise to powder flow problems. Shear cell techniques were used to measure the following powder flow properties: powder flowfunction, effective angle of internal friction and angle of wall friction. These measurements were used in assessing cohesion developed within the powders under compaction and adhesion to a stainless steel surface. The work investigated how fat content, free-fat content, particle size, moisture content, lactose content, amorphous lactose content and storage conditions influenced the flowability of the milk powders. Increased fat content reduced powder flowability especially when comparing 1% and 26% fat powders. Varying free-fat content showed no effect on flowability. Particle size had a major influence on flowability, as increasing the particle size significantly improved the flowability of powders with 1% and 26% fat content. The concentration of amorphous lactose present increased the susceptibility of powders for sorbing moisture, resulting in reduced flowability and caking. Finally, powder flow property measurements can be applied in the design of hoppers and silos that give consistent reliable flow, which is essential in powder handling and processing operations.
A case study was conducted on a group of undergraduate chemical engineering students to assess the relevance of attending lectures from a student perspective and to understand why these students attend and do not attend lectures with a view to developing approaches to teaching, which are of greater interest and benefit to student learning. The students were surveyed by means of a questionnaire-type survey, which collected both quantitative and qualitative data from them. The majority of students stated that lectures are still very beneficial to their learning and are not an out-of-date mode of education. The major reasons for lecture non-attendance were time priority and curriculum overload issues with other scholarly activities and poor quality teaching. The students provided a number of suggestions to improve lectures and lecture attendance, including the incorporation of active learning in lectures, linking lectures to assessment and adding extra value to what is already in the notes.
22 June 2009 in Particulate Science and Technology
In this work, a seeded batch cooling crystallizer was used to study dextrose monohydrate crystallization using in situ techniques. Experiments were conducted to investigate the influence of cooling profile (natural, linear, and controlled cooling) and seed mass on dextrose monohydrate crystallization. Two in situ techniques, Lasentec focused beam reflectance measurement (FBRM) and an in-line process refractometer for monitoring aqueous crystallization of dextrose monohydrate, were used. The seed mass and cooling profile were focused on, in particular, determining the effect of secondary nucleation and crystal growth rate on the final crystal size distribution, the evolution of supersaturation, and yield of dextrose monohydrate. Experimental results were analyzed to evaluate the kinetic constants from growth and nucleation power law functions with supersaturation. The results showed that increasing the seed mass decreased the level and the peak of supersaturation and increased the crystal growth rate. The experiment performed with natural cooling and with high seed mass resulted in the highest yield. Furthermore, the results showed a significant increase in the final crystal size with decreasing seed mass.
25 August 2011 in Particulate Science and Technology
The handling of powders in industry has been laden with problems caused by caking during storage and handling, whereby free flowing materials are transformed into lumps and agglomerates. It is of great importance for the manufacturers of bulk solid products to know whether and under what conditions the products are prone to cake. The objective of the work in this paper was to visually investigate the influence of relative humidity (RH) and humidity cycling on the caking behavior of powder particles in contact and to interpret the caking mechanism. A light microscope equipped with a digital camera was used to visually observe the caking of two particles in contact over time by taking a series of photographs. The following four food powders were studied: maltodextrin DE 21, sodium chloride (NaCl), skim milk powder (SMP), and a baby food powder. The maltodextrin and the baby food powders behaved similarly with sinter bridge formation being the caking mechanism. The NaCl and SMP behaved similarly with the caking mechanism being due to water bridge formation and solid bridge formation during low humidity exposure when the water vaporized leaving behind the dissolved solids in the bridge.