Keawprak Keawprak

Dr. Keawprak Keawprak


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 September 2011 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
KKKeawprak Keawprak
Keawprak Keawprak
SLS. Lao-Ubol
S. Lao-Ubol
CEC. Eamchotchawalit
C. Eamchotchawalit
ZSZ.M. Sun
Z.M. Sun

11 April 2024 in Buildings
Verified
Journal Article
Open access
PDF file
STSiriwan Thepruttana
Siriwan Thepruttana
JPJira Patthanavarit
Jira Patthanavarit
Montree HankoyMontree Hankoy
Montree Hankoy
MKMettaya Kitiwan
Mettaya Kitiwan
KKKeawprak Keawprak
Keawprak Keawprak
PTPhacharaphon Tunthawiroon
Phacharaphon Tunthawiroon
This study presents a novel approach in enhancing the flexural strength of sisal fiber cement composites by employing a dual coating technique with natural rubber latex and expanded perlite to the sisal fibers. The effects of different fiber content (0.25, 0.5, 0.75, 1, 1.25, and 1.5 wt%) and fiber length (1, 2, and 3 cm) on the physical and mechanical properties of sisal fiber cement were also studied. The physical properties, including bulk density and water absorption, were evaluated via the Archimedes method. Flexural strength was measured using the 3-point bending method, and microstructure was observed using a scanning electron microscope (SEM) and an optical microscope (OM). As the fiber content and length increase, the bulk density of the sisal fiber cement decreases. However, composites utilizing coated fibers consistently exhibit a higher bulk density than those utilizing uncoated fibers, attributed to enhanced adhesion and reduced porosity. The water absorption of sisal fiber cement increases with fiber content, but it is mitigated by the natural rubber latex coating, which prevents fiber–water absorption, and by expanded perlite, which reduces voids in the matrix. Composites containing coated fibers consistently exhibit superior flexural strength compared to those with uncoated fibers. The highest flexural strength values of 5.58 MPa were observed in composites utilizing 3 cm of coated fiber with 0.25 wt% fiber content. Microstructure analysis reveals a well-bonded interface in coated fibers, emphasizing the positive impact of coating on mechanical performance. The incorporation of coated sisal fibers effectively improves adhesion, water resistance, and flexural strength, offering sustainable and durable construction materials. The achieved results can serve as the guidelines for the development of a high-performance bio-based construction materials with improved durability and reduced environmental impact.

10 November 2023 in Suranaree Journal of Science and Technology
Verified
Journal Article
Closed access
ANAkawat Ngamkiatpaisan
Akawat Ngamkiatpaisan
Montree HankoyMontree Hankoy
Montree Hankoy
MKMettaya Kitiwan
Mettaya Kitiwan
KKKeawprak Keawprak
Keawprak Keawprak
PTPhacharaphon Tunthawiroon
Phacharaphon Tunthawiroon
Web site created using create-react-app

1 November 2022 in Chiang Mai Journal of Science
Verified
Journal Article
Closed access
KKKeawprak Keawprak
Keawprak Keawprak
PAPisuit Arkom
Pisuit Arkom
PLPracha Lao-Auyporn
Pracha Lao-Auyporn
NKNikorn Kaewpreak
Nikorn Kaewpreak
PWPimpilai Wannasut
Pimpilai Wannasut
AWAnucha Watcharapasorn
Anucha Watcharapasorn
In this study, the perlite-based insulating material is developed to meet ASTM C610 standards in a form of the board. Expanded perlite powders with a tapped density of 53 and 150 kg/m(3) were used in this study. Sodium silicate used as a proper binder at various concentrations was mixed with perlite powders. The homogeneous moist mixture was formed by uniaxial pressing at different compaction ratios. Specimens were dried at low temperatures (250-400 degrees C). Measurements of physical properties e.g., flexural strength, bulk density and thermal conductivity, were conducted. Perlite foam was set after drying, leading to an increase in its moisture resistance and strength. Compression molding also affected the density and strength of the products. Heat treatment after forming was carried out in order to dehydrate water molecules and bond particles together. The specimens were tested in accordance with ASTM C610 as a result of optimum conditions from perlite powder with a tapped density of 53 kg/m(3). Perlite foam board had been successfully fabricated with a bulk density of 205 kg/m(3), flexural strength of 434 kPa, compressive strength of 764 kPa and room temperature thermal conductivity of 0.056 W/m.K.

Verified
Journal Article
Open access
PDF file
PMPaniti Moolpradab
Paniti Moolpradab
Montree HankoyMontree Hankoy
Montree Hankoy
JZJianfeng Zhang
Jianfeng Zhang
KKKeawprak Keawprak
Keawprak Keawprak
MKMettaya Kitiwan
Mettaya Kitiwan
PTPhacharaphon Tunthawiroon
Phacharaphon Tunthawiroon
The utilization of locally sourced raw materials for lightweight aggregate (LWA) production has attracted increasing attention due to its potential for cost reduction and sustainable material development. This study investigates the effect of expanded perlite addition (10–40 wt%) on the physical, structural, and mechanical properties of LWAs derived from In Buri red clay, sintered at a relatively low temperature of 800 °C without a conventional high-temperature bloating process. X-ray diffraction (XRD) analysis revealed that quartz remained the dominant phase after sintering, with minor albite and residual illite, indicating limited phase transformation. Thermal analysis showed that major mass loss occurred below 600 °C, confirming that 800 °C is sufficient for removing volatile components. SEM observations demonstrated that increasing perlite content led to the development of a more porous and interconnected microstructure. As the expanded perlite content increased, the bulk density decreased from 1.31 to 0.80 g/cm3, while the apparent porosity and water absorption increased to 48.5% and 60.8%, respectively. Conversely, crushing strength decreased due to increased porosity. These results demonstrate that expanded perlite is an effective additive for tailoring the microstructure and performance of LWAs at low sintering temperature. The developed materials show strong potential for horticultural applications.