Waterlogging restricts root-zone oxygen availability and can impair seedling growth and leaf quality in mulberry. Root-zone aeration may reduce waterlogging injury, but its effects on root anaerobic metabolism, photosynthesis, oxidative stress, and leaf functional quality have not been well integrated. In this study, Morus alba L. ‘Longsang No. 1’ seedlings were subjected to four treatments: normal moisture without aeration (CK), normal moisture with intermittent root-zone aeration (RA), waterlogging without aeration (WL), and waterlogging with intermittent root-zone aeration (WL+RA). Waterlogging was maintained with a water layer 1–2 cm above the substrate surface, and root-zone aeration was supplied using an air pump and microporous aeration stones for 30 min every 4 h. Root-zone dissolved oxygen, growth traits, root activity, root fermentative indicators, root and leaf oxidative injury, gas exchange, chlorophyll fluorescence, antioxidant enzyme activities, and leaf quality-related traits were measured after 14 d of treatment. Waterlogging decreased root-zone dissolved oxygen from 6.62 to 1.69 mg L⁻¹. It also reduced plant height, total leaf area, shoot and root dry weight, root activity, Pn, Fv/Fm, Y(II), and ETR. In contrast, WL increased ADH and PDC activities, lactate and ethanol contents, MDA, H₂O₂, electrolyte leakage, and NPQ. Leaf 1-DNJ, polysaccharides, total phenolics, total flavonoids, DPPH, ABTS, and FRAP were also reduced under WL. Intermittent aeration increased root-zone dissolved oxygen to 4.64 mg L⁻¹ under waterlogging and partially alleviated many of these changes. WL+RA showed higher growth, root activity, photosynthetic performance, PSII photochemical efficiency, antioxidant enzyme activities, and leaf functional quality than WL. These results indicate that intermittent root-zone aeration was associated with better mulberry seedling performance under waterlogging, together with changes in root-zone oxygen status, fermentation metabolism, photosynthesis, oxidative balance, and leaf quality.

Wood- and lignocellulosic-residue-derived constituents have attracted increasing attention in cementitious materials because they may support clinker reduction, waste valorization, moisture regulation, crack control, and longer service life. This review synthesizes evidence on wood ash, wood-derived biochar, and wood or lignocellulosic fibers in low-clinker and low-carbon-oriented cementitious systems, with emphasis on severe cold service involving freeze–thaw cycling, salt freezing, and chloride ingress. This review clarifies the evidence boundaries among direct wood-derived materials and related biomass or lignocellulosic analogues, because wood ash, non-wood biomass ashes, such as bamboo ash and bagasse ash, wood fiber, and non-wood plant fibers cannot be treated as equivalent materials. Wood ash is best regarded as a controlled partial binder replacement or filler whose performance depends on combustion temperature, oxide composition, alkali content, residual carbon, fineness, and water demand. Biochar is more appropriately treated as a low-dosage functional additive, commonly in the range of approximately 1–3 wt.% of binder, where it may assist internal curing, nucleation, moisture redistribution, and pore regulation; excessive dosage can increase porosity and reduce mechanical or transport performance. Wood and lignocellulosic fibers mainly contribute to crack control, toughness, and post-cracking behavior, but their effectiveness is limited by water absorption, swelling, lignin- and extractive-related hydration interference, and long-term interfacial degradation in alkaline matrices. Across these material classes, engineering performance is governed by the interfacial transition zone, pore-size distribution, moisture state, air–void compatibility, and exposure-specific durability response. The main contribution of this review is to propose a boundary-conscious framework for material classification, quantitative comparison, mixture-design screening, and severe-cold durability qualification. Future application requires source-specific characterization, water-demand control, treated fibers, low-dosage biochar optimization, and service-informed testing that couples freeze–thaw cycling, chloride transport, saturation state, and microstructural verification.