Hong Zhang

Dr. Hong Zhang


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 February 2025 in Materials
Verified
Journal Article
Open access
PDF file
HZHui Zhang
Hui Zhang
LFlu feng
lu feng
WMWeibo Mao
Weibo Mao
QLQuanming Liu
Quanming Liu
LZLiang Zhao
Liang Zhao
HZHong Zhang
Hong Zhang
To enhance the mechanical properties and high-temperature performance of cordierite–mullite composite ceramics, yttrium oxide (Y2O3), a rare earth metal oxide, was employed as a sintering aid to fabricate these composites via in situ synthesis and non-pressure sintering. This study systematically investigated the formation mechanisms of the cordierite and mullite phases and examined the effects of yttrium oxide on the densification behavior, mechanical properties, volumetric stability, and thermal shock resistance. The results indicate that incorporating yttrium oxide (1.5–6.0 wt%) not only promoted the formation of the cordierite phase but also refined the microstructure and enhanced the thermal shock stability at a sintering temperature of 1350 °C. An optimal addition of 3 wt% yttrium oxide ensures that the primary phases are cordierite and mullite, with a microstructure characterized by uniformly distributed micropores, hexagonal short-columnar cordierite, and interlocking rod-like mullite, thereby significantly improving both the mechanical properties and thermal shock stability. Specifically, the room-temperature compressive strength increased by 121%, the flexural strength increased by 177%, and, after three thermal shock cycles at 1100 °C, the retention rates for compressive and flexural strengths were 87.66% and 71.01%, respectively. This research provides a critical foundation for enhancing the mechanical properties and high-temperature service performance of cordierite–mullite saggers used in lithium battery cathode materials.

23 June 2026 in Processes
Verified
Journal Article
Open access
PDF file
HZHong Zhang
Hong Zhang
JFJia Fu
Jia Fu
The constitutive analysis model and hot processing map of the ZM6 alloy across various deformation conditions were investigated during hot compression experiments. True stress-strain curves within 300–450 °C and 0.0001–0.1 s−1 were obtained from compression tests on a Gleeble-1500 platform. The results showed that higher strain rates (e.g., 0.1 s−1) induced pronounced work hardening, whereas high temperatures (300–400 °C) combined with low strain rates (10−4 s−1) promoted conditions conducive to dynamic recrystallization (DRX), leading to a softening tendency of steady-state flow stress. Additionally, a modified strain-compensated constitutive model was built for flow stress prediction. Material constants were plotted as fifth-order polynomial functions of strain (0.025–0.80) for precise stress predictions. The derived activation energy (Q = 182.38 kJ/mol) falls within the typical range for Mg-RE alloys. Leave-one-temperature-out cross-validation showed average AARE values of 7.2–9.8%, demonstrating the model’s interpolation capability and its sensitivity to extrapolation. Cross-validation within the training dataset showed reasonable consistency between experimental and predicted stresses (R > 0.997, AARE < 4.35%). Using the dynamic materials model, hot processing maps identified safe deformation zones and instability zones of the ZM6 alloy. Flow instability was observed at strain rates >0.01 s−1, particularly at low temperatures (300–350 °C). Optimal processing windows appeared in high-energy dissipation (η > 30%) regions, e.g., 400–450 °C/10−4–10−3 s−1. Optical microscopy confirmed that at high temperatures (≥400 °C) and low strain rates (≤0.001 s−1), a uniform, fine-grained, fully recrystallized structure can be obtained, whereas low temperatures (350 °C) and high strain rates (0.1 s−1) produce coarse elongated grains with limited DRX, consistent with the instability regime predicted by the processing maps. Under intermediate conditions (e.g., 400 °C, 0.01 s−1), a bimodal grain distribution indicates incomplete recrystallization. Although EBSD analysis was not performed in this study, the optical microstructures directly validate the predicted safe and unstable windows. Together, all these findings provide preliminary model-based guidance for optimizing hot working parameters to balance microstructural stability and processing efficiency.