Lignin is a type of natural aromatic material with potential application prospects obtained from lignocellulosic biomass. Recently, the valorization of lignin has received increasing attention from both industry and academia. However, there is still a challenge in the efficient valorization of lignin due to the complexity and stability of the lignin structure. Recent work has been focused on the catalytic depolymerization of lignin to explore a promising and efficient way to valorize lignin into chemicals with high value and biofuels. Considerable research has focused on catalysts, solvents, and reaction parameters during the lignin depolymerization process, which significantly affects product distribution and productivity. Thus, in a catalytic depolymerization process, both catalysts and solvents have a significant influence on the depolymerization effect. This review article assesses the current status of the catalytic hydrogenolysis of lignin, mainly focusing on the solvents and catalysts during the reaction. First, various solvents applied in the lignin depolymerization reactions are extensively overviewed. Second, the recent progress of metal catalysts as well as their supports is summarized. Furthermore, a discussion of the challenges and prospects in this area is included.
With the continuous depletion of fossil resources and the deterioration of the global climate, it is particularly urgent to find green and sustainable renewable resources to replace non-renewable resources. Renewable biomass, which converts and stores light energy into chemical energy through photosynthesis by green plants, has received widespread attention due to its simultaneous resource and energy properties. Therefore, this article focuses on lignocellulose, an important component of biomass, in the fields of chemical conversion and high-value-added chemical preparation. A detailed review was conducted on the application of catalysts in biomass bio-char, bio-oil, bio-gas, and high-value added chemicals and their derivatives, represented by 5-hydroxymethylfurfural (5-HMF) and levulinic acid (LA). At the same time, the difficulties and challenges encountered by catalysts in biomass conversion were analyzed, and new ideas were proposed for future development directions, so as to provide new development pathways for efficient and green conversion of biomass into biomass energy and high-value-added chemicals.
The co-contamination of nitrate nitrogen (NO3−-N) and tetracycline (TC) in aquaculture water has caused serious environmental and health problems. Bioremediation is a promising approach for the removal of NO3−-N and TC. However, free bacteria are sensitive to environmental variation, limiting its application. In this study, a bacterial strain with high NO3−-N and TC degradation ability, Bacillus cereus W2, was isolated and immobilized on wheat straw biochar by an adsorption method. The effect of immobilization conditions, including biochar dosage, inoculum amount, and immobilization time on NO3−-N and TC removal was explored. The degradation abilities of the biochar-immobilized Bacillus cereus W2 under different nitrate and TC concentrations was investigated. Results showed that the prepared biochar had abundant functional groups such as -COOH, -OH, -C=C-OH, etc., which have good affinity for microbial cell membranes and are conducive to the adhesion and proliferation of microbial cells. The highest NO3−-N and TC removal efficiencies of 99.50% and 78.60% after 24 h were obtained under a biochar dosage of 4 mg·mL−1, microbe inoculation amount of 40%, and immobilization time of 24 h. The immobilized Bacillus cereus W2 performed better NO3−-N and TC removal than the free cells under different initial NO3−-N and TC concentrations. The enhanced removal of NO3−-N by the biochar-immobilized Bacillus cereus W2 may be attributed to the promoted expression level of functional genes involved in denitrification (nirS, norB, and nosZ). The biochar-immobilized Bacillus cereus W2 demonstrates potential for treating various nitrate-antibiotic co-contaminated wastewaters, including those from livestock farming, aquaculture systems, and pharmaceutical industries.
24 October 2025 in Journal of Environmental Management
In this paper, nano-silica particles were prepared from chlorosilane residue liquid using an inverse micro-emulsions system formed from octylphenyl polyoxyethylene ether (TX-100)/n-hexanol/cyclohexane/ammonia. The influence of different reaction conditions on the morphology, particle size, and dispersion of nano-silica particles was investigated via single-factor analysis. When the concentration of chlorosilane residue liquid (0.08 mol/L), hydrophile-lipophilic-balance (HLB) values (10.50), and the concentration of ammonia (0.58 mol/L) were under suitable conditions, the nano-silica particles had a more uniform morphology, smaller particle size, and better dispersion, while the size of the nano-silica particles gradually increased with the increase in the molar ratio of water to surfactant (ω). The prepared nano-silica was characterized through XRD, FT-IR, N2 adsorption/desorption experiments, and TG-DSC analysis. The results showed that the prepared nano-silica was amorphous mesoporous silica, and that the BET specific surface area was 850.5 m2/g. It also had good thermal stability. When the temperature exceeded 1140 °C, the nano-silica underwent a phase transition from an amorphous form to crystalline. This method not only promoted the sustainable development of the polysilicon industry, it also provided new ideas for the protection of the ecological environment, the preparation of environmental functional materials, and the recycling of resources and energy.
This study aims to explore the preparation process and properties of unburned lightweight aggregate using red mud synergistically with fly ash, granulated blast-furnace slag, and other multi-source solid wastes. Curing regimes and alkali-activated systems were controlled. Their effects on physical properties and environmental safety of lightweight aggregate were systematically evaluated. Results show that curing temperature and alkali activator exert significant synergistic effects on physical properties of lightweight aggregates. Steam curing performs better than standard curing. Performance improves with increasing steam temperature. Sodium silicate solution with a modulus of 1.0 is determined as the optimal activator. Under 90 °C steam curing, Sample D2 achieves the best overall performance. Its cylinder compressive strength reaches 6.92 MPa. 1 h water absorption is 14.8%. Softening coefficient is 0.93. Porosity is as low as 31.07%. Microscopic analysis reveals that higher curing temperature significantly accelerates the hydration reaction of the RMLWA system. It promotes the formation of abundant cementitious products such as C-S-H gel. These products fully fill internal pores and microcracks of the aggregate. A dense three-dimensional network skeleton structure is finally formed. For environmental safety, heavy metal leaching concentrations of steam-cured samples are generally lower than those of standard-cured samples. This study realizes high-value resource utilization of industrial solid wastes. It also provides a new technical route for the development of green building lightweight aggregate.