The deterioration of human oral microbiota is known to not only cause oral diseases but also to affect systemic health. Various environmental factors are thought to influence the disruption and restoration of the oral ecosystem. In this study, we focused on the effect of nitric oxide (NO) produced by denitrification and NO synthase enzymes on dental plaque microbiota. Interdental plaques collected from 10 subjects were exposed to NO donor sodium nitroprusside (SNP) and then cultured in a specialized growth medium. Depending on the concentration of exposed SNP, a decrease in α-diversity and a continuous change in β-diversity in the dental plaque community were shown by sequencing bacterial 16S rRNA genes. We also identified eight operational taxonomic units that were significantly altered by NO exposure. Among them, the exposure of NO donors to Fusobacterium nucleatum cells showed a decrease in survival rate consistent with the results of microbiota analysis. Meanwhile, in addition to NO tolerance, an increase in the tetrazolium salt-reducing activity of Campylobacter concisus cells was confirmed by exposure to SNP. This study provides an overview of how oral plaque microbiota shifts with exposure to NO and may contribute to the development of a method for adjusting the balance of the oral microbiome.

Contamination of implants is inevitable during different steps of production as well as during the clinical use. We devised a new implant cleaning strategy to restore the bioactivities on dental implant surfaces. We evaluated the efficiency of the Finevo cleaning system, and Ultraviolet and Plasma treatments to decontaminate hydrocarbon-contaminated titanium disks. The surfaces of the contaminated titanium disks cleaned using the Finevo cleaning system were similar to those of the uncontaminated titanium disks in scanning electron microscopy and X-ray photoelectron spectroscopy analysis, but no obvious change in the roughness was observed in the scanning probe microscopy analysis. The rat bone marrow mesenchymal stem cells (rBMMSCs) cultured on the treated titanium disks attached to and covered the surfaces of disks cleaned with the Finevo cleaning system. The alkaline phosphatase activity, calcium deposition, and osteogenesis-related gene expression in rBMMSCs on disks cleaned using the Finevo cleaning system were higher compared to those in the ultraviolet and plasma treatments, displaying better cell functionality. Thus, the Finevo cleaning system can enhance the attachment, differentiation, and mineralization of rBMMSCs on treated titanium disk surfaces. This research provides a new strategy for cleaning the surface of contaminated titanium dental implants and for restoration of their biological functions.

Recently, polyetheretherketone (PEEK) has shown promising dental applications. Surface treatment is essential for dental applications owing to its poor surface energy and wettability; however, no consensus on an effective treatment method has been achieved. In this study, we attempted to carboxylate PEEK sample surfaces via Friedel–Crafts acylation using succinic anhydride and AlBr₃. The possibility of further chemical modifications using carboxyl groups was examined. The samples were subjected to dehydration–condensation reactions with 1H,1H-pentadecafluorooctylamine and N,N’-dicyclohexylcarbodiimide. Furthermore, the sample’s surface properties at each reaction stage were evaluated. An absorption band in the 3300–3500 cm⁻¹ wavenumber region was observed. Additionally, peak suggestive of COOH was observed in the sample spectra. Secondary modification diminished the absorption band in 3300–3500 cm⁻¹ and a clear F1s signal was observed. Thus, Friedel–Crafts acylation with succinic anhydride produced carboxyl groups on the PEEK sample surfaces. Further chemical modification of the carboxyl groups by dehydration-condensation reactions is also possible. Thus, a series of reactions can be employed to impart desired chemical structures to PEEK surfaces.

Recently, polyetheretherketone (PEEK) has shown promising dental applications; although surface treatment is essential for dental applications owing to its poor surface energy and wettability, no consensus on an effective treatment method has been achieved. In this study, we attempt to carboxylate PEEK sample surfaces via Friedel–Crafts acylation using succinic anhydride and AlBr3. The possibility of further chemical modifications using carboxyl groups is examined. The samples are subjected to dehydration–condensation reactions with 1H,1H-pentadecafluorooctylamine and N,N'-dicyclohexylcarbodiimide. The sample surface properties at each reaction stage are evaluated. An absorption band in the 3300–3500 cm-1 wavenumber region is observed. Additionally, peak suggestive of COOH is observed in the sample spectra. Secondary modification diminished the absorption band in 3300–3500 cm-1 and a clear F1s signal is observed. Thus, Friedel–Crafts acylation with succinic anhydride produces carboxyl groups on the PEEK sample surfaces. Further chemical modification of the carboxyl groups by dehydration-condensation reactions is also possible. Thus, a series of reactions can be employed to impart desired chemical structures to PEEK surfaces.

Additive manufacturing using vat photopolymerization (VPP) resin materials has gained attention for fabricating dental prostheses; however, the effects of material type and build angle on their properties remain unclear. We compared the mechanical properties of two filler-containing VPP hybrid resins, SprintRay Ceramic Crown (CC) and OnX Tough 2 (OT), with those of a conventional polymethyl methacrylate (PMMA) disc material, and evaluated the influence of build angle on surface characteristics, dimensional accuracy, and mechanical performance. Specimens were fabricated using a DLP system at build angles of 0°, 45°, and 90°. Vickers hardness, surface morphology and roughness, dimensional deviations, flexural strength, elastic modulus, and fracture energy were assessed according to relevant standards. CC exhibited significantly higher hardness and elastic modulus than PMMA and OT, whereas OT showed the highest fracture energy. Surface morphology and roughness were strongly affected by build angle, with 45° producing distinct periodic patterns and increased roughness. Dimensional evaluation revealed a tendency toward overbuilding, particularly in the vertical direction at 45°. Flexural properties were also influenced by build angle, with 45° generally providing favorable performance. Both material composition and build angle affect VPP-fabricated dental resin performance, highlighting the importance of appropriate material and processing selection for clinical applications.

Additive manufacturing using vat photopolymerization (VPP) resin materials has gained attention for fabricating dental prostheses; however, the effects of material type and build angle on their properties remain unclear. We compared the mechanical properties of two filler-containing VPP hybrid resins, SprintRay Ceramic Crown (CC) and OnX Tough 2 (OT), with those of a conventional polymethyl methacrylate (PMMA) disc material, and evaluated the influence of build angle on surface characteristics, dimensional accuracy, and mechanical performance. Specimens were fabricated using a DLP system at build angles of 0°, 45°, and 90°. Vickers hardness, surface morphology and roughness, dimensional deviations, flexural strength, elastic modulus, and fracture energy were assessed according to relevant standards. CC exhibited significantly higher hardness and elastic modulus than PMMA and OT, whereas OT showed the highest fracture energy. Surface morphology and roughness were strongly affected by build angle, with 45° producing distinct periodic patterns and increased roughness. Dimensional evaluation revealed a tendency toward overbuilding, particularly in the vertical direction at 45°. Flexural properties were also influenced by build angle, with 45° generally providing favorable performance. Both material composition and build angle affect VPP-fabricated dental resin performance, highlighting the importance of appropriate material and processing selection for clinical applications.