Introduction. Modern research aimed at improving the efficiency of the workpart procedures emphasizes the importance of taking into account the effect of periodic disturbances on the cutting dynamics. However, few works consider uncontrolled periodic disturbances, whose sources are spindle units and the supporting system of the machine. These disturbances also have a significant impact on the final quality indicators of the cutting process. Therefore, an urgent task in the mechanical engineering technology is to establish patterns of the effect of uncontrolled disturbances on the dynamics of the cutting process, which is particularly important for the development of systems for the automated selection of operating conditions or vibration diagnostics systems. This research is aimed at determining the mechanism of influence of periodic fluctuations of processing parameters caused by vibration disturbances on the temperature of the front face of the turning cutter, which is the key indicator of the development of diffusion wear of the carbide tool.Materials and Methods. The study of the effect of periodic disturbances on the temperature of the front face of the tool was performed in two stages. At the first stage, based on a full-scale experiment on finishing longitudinal turning of blanks made of 10GN2MFA steel with cutters with T15K6 hard alloy plates, the parameters of the disturbance model in the system were identified, namely, the oscillatory accelerations of the tool under its wear. The vibration characteristics of the 16K20 universal lathe were measured using a vibration stand assembled on the basis of AP2089–100–3.3–02B vibration transducers, with a signal sampling frequency of 10 kHz. At the second stage, a digital study of the simulated disturbances and their effect on the dynamics of the cutting process was carried out. The results of the experiments were analyzed to compare the calculated maximum temperature of the front face of the tool at the moments when one of the specified output parameters of processing, obtained as a result of digital modeling, reaches an extreme value under the impact of periodic disturbances.Results. It has been established that fluctuations in the parameters of operating cutting modes caused by periodic disturbances lead to temperature fluctuations in the contact zone of the tool and the blank. The greatest impact on the temperature in the cutting system under study was exerted by the combination of processing parameters at the moments of reaching extreme feed values. However, when fluctuations in cutting depth and speed reached extreme values, no significant changes in contact temperature were observed.Discussion and Conclusion. The results of the conducted research emphasize the importance of analyzing the effect of periodic disturbances on pulse changes in contact temperature in the processing zone. The presented model of the relationship between tool vibrations and temperature in the cutting zone can be used to optimize turning modes. The criterion of optimality is the minimization of tool wear, which is determined on the basis of an analysis of temperature fluctuations and vibration activity signals of the tool.
30 March 2022 in Advanced Engineering Research (Rostov-on-Don)
Introduction. This paper discusses tribomechanical characteristics of experimental hard alloys with a modified cobalt binder under friction without lubrication on hard-to-cut materials – stainless steel and titanium alloy. The research objective is to evaluate the process of friction interaction for each friction pair according to a number of parameters, and to determine the optimal combinations of “experimental hard alloy – structural material” on the basis of the established tribological indicators.Materials and Methods. Tribological tests of hard alloys were carried out using a cylinder-to-disc friction scheme for different sliding speeds and temperatures under constant load without the use of lubricants. Comparison of the friction interaction process was carried out by the frictional force, volumetric wear and roughness of the friction tracks on the counterbody. Stainless steel 12H18N9Т and titanium alloy ВТ3-1 were used as counterbody materials. The resistance of experimental compositions to the abrasive type of wear was determined through measuring the surface dynamic microhardness on a scanning nanohardness tester by analyzing the thickness of the scratches caused by the indenter.Results. According to the results of surface microindentation, the experimental alloys 2.22 (binder 5.65% Co + l.8% Mo + 0.6% Ti) and 2.23 (binder 5.1% Co + 2.7% Mo + 0.61 % Ti) are characterized by the highest microhardness. For these materials, the average scratch width at various forces was minimal. During tribological tests, the best frictional characteristics were recorded for stainless steel in combination with experimental alloy 2.22, and for the friction pair “titanium alloy VT3-1 — hard alloy 2.23”. The friction of this combination of materials was characterized by low friction coefficients with a low level of fluctuations, minimal wear of samples, and changes in the initial microrelief of their surfaces.Discussion and Conclusions. As a result of the research, the optimal friction pairs from the point of view of tribological interaction were established, specifically “titanium alloy VT3-1 — hard alloy 2.23” and “stainless steel 12X18N9T – hard alloy 2.22”. The frictional interaction for these combinations of materials is characterized by minimal volumetric wear, which will contribute to increasing the wear resistance of the tool in the areas of elastic contact on the front and rear surfaces.
1 November 2020 in IOP Conference Series: Materials Science and Engineering
The article is devoted to the critical problem of studying the dependencies of temperature and cutting forces on the entropy of tool materials (high-speed steels - HSS). The high wear resistance of the cutting tool is closely related to the entropy of tool materials. However, the relationship of entropy as structural sensitive characteristic with temperature and forces during machining processes is poorly investigated. The experimental studies were carried out on the engine lathe with an infinitely variable regulation of spindle rotation frequencies, equipped with a measuring complex, allowing cutting forces and temperature recording at different cutting speeds. It has been established experimentally that at all cutting speeds in the studied range the smallest values of cutting forces and contact temperatures were characteristic for cutting tools made of HSS with high levels of thermal entropy. Thus, the thermal entropy of HSS can be used to the preliminary assessment of relative values of cutting forces and temperatures during the processing of steels which characteristics are strongly connected with wear rates and reliability of cutting tools.
Introduction. The formation of the surface of a part when processing it on a metal-cutting machine is based on properly selected cutting modes. Complex methods of ensuring the specified quality of the part surface also take into account the tool geometry, its condition, and include corrections for tool deviation from the trajectory set by the CNC system under the influence of kinematic disturbances and spindle wavering. Subject. The paper analyzes the relationship between cutting modes and dynamic characteristics of the turning process, and its mapping into surface roughness. The aim of the work is to evaluate the influence of technological cutting modes taking into account the vibration activity of the tool on the roughness of the machined surface by means of simulation modeling. Method and methodology. Mathematical simulation of the dynamics of the cutting process is given, on the basis of which a digital simulation model is built. A methodology of using the simulation model for determining optimal cutting modes and predicting surface roughness taking into account tool vibrations is proposed. By means of experiments and analysis of the frequency characteristics of tool vibrations, the created model is validated, parameters of the cutting forces model subsystem and dynamic tool subsystem are specified, and geometrical topologies of the part surface are constructed. The calculated cutting forces are compared with experimental forces, and similar patterns and levels of characteristics are observed. An assessment of the optimality of the selected cutting modes is proposed based on the analysis of the tool vibration spectrum relative to the workpiece and the results of the numerical model simulation. Results and Discussion. A comparison of the results of digital modeling of the geometrical surface of the workpiece and the real surface obtained during the field experiment is given. It is shown that the roughness of the real surface obtained by machining with constant cutting modes varies relative to the surface roughness of the simulation model within the limits of not more than 0.066 µm.