Extensive vertical deformation (>4.5 m) observed at Sierra Negra volcano Galápagos, Ecuador, between 1992 and the 2005 eruption led scientists to hypothesize that repeated faulting events relieved magma chamber overpressure and prevented eruption. To better understand the catalyst of the 2005 eruption, thermomechanical models are used to track the stress state and stability of the magma storage system during the 1992–2005 inflation events. Numerical experiments indicate that the host rock surrounding the Sierra Negra reservoir remained in compression with minimal changes in overpressure (~10 MPa) leading up to the 2005 eruption. The lack of tensile failure and minimal overpressure accumulation likely inhibited dike initiation and accommodated the significant inflation without the need for pressure relief through shallow trapdoor faulting events. The models indicate that static stress transfer due to the Mw 5.4 earthquake 3 hr prior to the eruption most likely triggered tensile failure and catalyzed the 2005 eruption.
The Laguna del Maule volcanic field is a large rhyolitic magmatic system in the Chilean Andes, which has exhibited frequent eruptions during the past 20 ka. Rapid surface uplift (>20 cm/year) has been observed since 2007 accompanied by localized earthquake swarms and microgravity changes, indicating the inflating magma reservoir may interact with a preexisting weak zone (i.e., Troncoso fault). In this investigation, we model the magma reservoir by data assimilation with Interferometric Synthetic Aperture Radar data. The reservoir geometry is comparable to the magma body inferred by seismic tomography, magnetotelluric, and gravity studies. The models also suggest that a weak zone, which has little effect on surface displacement, is important as a fluid transport channel to promote earthquakes and microgravity changes. In particular, concentrated dilatancy within the weak zone facilitates the microfracture formation during reservoir inflation. High‐pressure fluid can inject into the weak zone from the magma reservoir to trigger earthquakes and further migrate upward to create positive gravity changes by occupying unsaturated storages. The pore pressure will then decrease, halting the seismicity swarm until the next cycle. This “hydrofracturing” process may release some accumulated stress along the magma reservoir delaying an eventual eruption in turn. Besides, the resultant models are propagated forward in time to evaluate potential stress trajectories for future unrest.
1 September 2017 in Journal of Volcanology and Geothermal Research
Forecasting the onset of a volcanic eruption from a closed system requires understanding its stress state and failure potential, which can be investigated through numerical modeling. However, the lack of constraints on model parameters, especially rheology, may substantially impair the accuracy of failure forecasts. Therefore, it is essential to know whether large variations and uncertainties in rock properties will preclude the ability of models to predict reservoir failure. A series of two‐dimensional, axisymmetric models are used to investigate sensitivities of brittle failure initiation to assumed rock properties. The numerical experiments indicate that the deformation and overpressure at failure onset simulated by elastic models will be much lower than the viscoelastic models, when the timescale of pressurization exceeds the viscoelastic relaxation time of the host rock. Poisson's ratio and internal friction angle have much less effect on failure forecasts than Young's modulus. Variations in Young's modulus significantly affect the prediction of surface deformation before failure onset when Young's modulus is < 40 GPa. Longer precursory volcano‐tectonic events may occur in weak host rock (E < 40 GPa) due to well‐developed Coulomb failure prior to dike propagation. Thus, combining surface deformation with seismicity may enhance the accuracy of eruption forecast in these situations. Compared to large and oblate magma systems, small and prolate systems create far less surface uplift prior to failure initiation, suggesting that more frequent measurements are necessary.
Using recent advancements in high-performance computing data assimilation to combine satellite InSAR data with numerical models, the prolonged unrest of the Sierra Negra volcano in the Galápagos was tracked to provide a fortuitous, but successful, forecast 5 months in advance of the 26 June 2018 eruption. Subsequent numerical simulations reveal that the evolution of the stress state in the host rock surrounding the Sierra Negra magma system likely controlled eruption timing. While changes in magma reservoir pressure remained modest (<15 MPa), modeled widespread Mohr-Coulomb failure is coincident with the timing of the 26 June 2018 moment magnitude 5.4 earthquake and subsequent eruption. Coulomb stress transfer models suggest that the faulting event triggered the 2018 eruption by encouraging tensile failure along the northern portion of the caldera. These findings provide a critical framework for understanding Sierra Negra’s eruption cycles and evaluating the potential and timing of future eruptions.