Turbine tip clearance of aero-engine is important to engine performance. Proper control of rotor tip clearance contributes to engine efficiency improvement and fuel consumption reduction. Therefore, accurate tip clearance measurement is essential. The inductive measurement method is one of the non-contact distance measurement methods, which has the characteristics of high sensitivity, fast response speed and strong anti-interference ability. Based on the principle of inductive sensor measuring tip clearance, the ambient temperature change will cause the material electromagnetic performance change for the conductivity and permeability varies with temperature. The calibration experiment was conducted to obtain the sensor resolution and sensing range. The effect of temperature on sensor parameters was extracted from high temperature experiment data. Results show the resolution of planar coil made of platinum wire can be 10 μm and the maximum sensing range can reach 5 mm. At temperature from 500 ℃ to 1100 ℃, coil inductance almost does not change with temperature while coil resistance varies exponentially with temperature, that means the coil inductance variation can reflect the tip clearance change and resistance can indicate the measuring temperature.

Turbine tip clearance of aero-engine is important to engine performance. Proper tip clearance can reduce the gas leakage over turbine blade tips and improve the engine efficiency of turbo machinery and reduce the fuel consumption. Therefore, accurate tip clearance measurement is essential. The inductive measurement method is one of the non-contact distance measurement methods, which has the characteristics of high sensitivity, fast response speed, and strong anti-interference ability. Based on the principle of inductive sensor measuring tip clearance, the ambient temperature change may cause the material electromagnetic performance change for the conductivity and permeability varies with temperature. In order to verify the temperature effect on the sensor performance, the repeated calibration experiments were carried out to obtain the sensor repeatability error of 5.4%. Then, the sensor was calibrated in the range of 0 mm–4 mm clearance at temperature from 600 °C to 1000 °C and obtained the measurement error of 4.6%. Results indicate when the temperature ranged from 600 °C to 1000 °C, clearance measurement error is smaller than the sensor repeatability error so the temperature effect on the sensor characteristics can be ignored. This conclusion makes the sensor promising for monitoring the blade tip clearances at various temperature environment.

Eddy current sensors are increasingly being used to measure the dynamic blade tip clearance in turbines due to their robust anti-interference capabilities and non-contact measurement advantages. However, the current research primarily focuses on enhancing the performance of eddy current sensors themselves, with few studies investigating the influence of turbine rotor parameters on the measurements taken by these sensors for dynamic blade tip clearance. Hence, this paper addresses this gap by using COMSOL Multiphysics 6.2 software to establish a finite model with circuit interfaces. Additionally, the model’s validity was verified through experiments. This model is used to simulate the voltage output of the sensor and the measurement of dynamic blade tip clearance under various rotor parameters. The results indicate that the length and number of blades, as well as the hub radius, significantly affect the sensor voltage output in comparison to rotation speed. Furthermore, we show that traditional static calibration methods are inadequate for measuring dynamic blade tip clearance using eddy current sensors. Instead, it is demonstrated that incorporating rotor parameters into the calibration of eddy current sensors can enhance the accuracy of dynamic blade tip clearance measurements.

Given the increasing application of eddy current sensors for measuring turbine tip clearance in aero engines, enhancing the performance of these sensors is essential for improving measurement accuracy. This study investigates the influence of coil shape on the measurement performance of planar eddy current sensors and identifies an optimal coil shape to enhance sensing capabilities. To achieve this, various coil shapes—specifically circular, square, rectangular wave, and triangular wave—were designed and fabricated, featuring different numbers of turns for the experiment at room temperature. By employing a method for calculating coil inductance, the performance of each sensor was evaluated based on key metrics: measurement range, sensitivity, and linearity. Experimental results reveal that the square coil configuration outperforms other shapes in overall measurement performance. Notably, the square coil demonstrated a measurement range of 0 mm to 8 mm, a sensitivity of 0.115685 μH/mm, and an impressive linearity of 98.41% within the range of 0 mm to 2 mm. These findings indicate that the square coil configuration enhances measurement capabilities. The conclusions drawn from this study provide valuable insights for selecting coil shapes and optimizing the performance of planar eddy current sensors, thereby contributing to the advancement of turbine tip clearance measurement techniques in aero engines.