A comprehensive review is conducted on the failures in the field of manufacturing and installation of E-glass fiber reinforced pipes (GFRP).Some of the failures which are mainly encountered after the installation of E-Glass fiber reinforced pipes are the for nation of air bubbles in between the polyester resin layer and the surface film, dispersion of moisture in between the tubing outer and inner layers after installation, heat released in between the layers of E-glass fiber reinforced pipes due to exothermic reaction which in turn results in the formation of cracks on the surface of the pipe. The recent findings and challenges performed in conducting research regarding the deterioration caused in glass fiber reinforced pipes are highlighted and each type of failure that was identified was illustrated with an appropriate high resolution photograph .Performing creep resistance and fatigue analysis are new aspects which are still requited to be analyzed which ave not been stated in the literature which are nominated.
26 June 2023 in Journal of The Institution of Engineers (India): Series D
This paper reports the split disk test (as in ASTM D 2290) modified to characterize the stress–strain behaviour of two different GFRP rings using a simple specimen preparation methodology. To compare the split disk ultimate strains, GFRP confined glass fiber rings made of different thicknesses, i.e., 1.75 mm, 2.50 mm and 3.25 mm were tested under uni-axial tensile tests after being wrapped with E-glass and S-glass GFRP fabrics. The results obtained from the modified split-disk tests on E-glass composites were compared with the results obtained from S-glass composites. In addition, the split-disk tests of selected composite specimens were simulated using a finite element method. Strain efficiency factors were then determined for design applications which are in good agreement with the experimental data.
6 August 2020 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Consequences of sea water absorption on the impact behaviour of glass/epoxy composite elbow pipe joints were experimentally investigated. Glass-epoxy elbow pipe joints using E-glass and S-glass were fabricated via the hand layup method. The pipe joints were immersed in water as per the current conditions for 0, 3 and 6 months. The relation between the unaged and aged samples was studied by calculating the contact force, displacement and absorbed energy values from the impact tests. Therefore, it is concluded that sea water raised the ageing period of both E-glass/epoxy and S-glass/epoxy fibre-reinforced composite elbow pipe joints which resulted in the degradation between the fibre and resin interface and which was prominent in the elbow joints fabricated with E-glass rather than the one’s fabricated with the proposed S-glass fibre.
1 January 2021 in International Journal of Surface Engineering and Interdisciplinary Materials Science
In the current research work performed, the consequences caused in the casting aluminum alloy specimen due to mechanical mould vibrations are examined. Mould vibration throughout the casting provides decreased rate of shrinkage, good morphology, surface finish and lesser probability of hot tear. In this research work, the effect of mould vibration during solidification of Aluminum A-1050 alloys for dissimilar values of wavelengths at a permanent pouring temperature has been investigated to understand the modification in microstructure and mechanical properties after casting. The Al A-1050 casting has been made in a metal mould with different vibrations. The frequencies are varied from 15Hz to 50 Hz during the casting process. A casting has been made with different vibration as well to compare the results of castings with vibration frequencies. The experimental outcomes exhibited substantial grain refinement and significant increase in tensile strength and hardness of the castings with mechanical mould vibration during the duration and after solidification.
19 March 2023 in Advances in Materials and Processing Technologies
Casting is a technique used to prepare machinery parts. Casting during vibration is one of the techniques used to improve the properties of material. In this paper, the effect of mould vibration on the properties of gravity die casting alloys is studied. This process decreases the porosity, holes and increase in the grain refinement of cast alloy. Aluminium 6082 T6 alloy is made by casting process, with and without vibration. The frequencies varied from 0 Hz to 45 Hz. The material is tested on electronic tensiometer and vickers hardness to check its tensile strength and hardness. The outcomes showed improvement in grain refinement and properties when vibration is applied during casting. With this improvement, it can be widely used in trusses, bridges, cranes and transport applications.