As the siting of wind turbines increasingly transitions from shallow water to offshore deep-water locations, improving the platform stability of floating offshore wind turbines is becoming a growing concern. By coupling a porous shell commonly used in traditional marine structures, with a FOWT (floating wind turbine platform), a new spar-buoy with a porous shell was designed. A numerical model investigating the coupling effect of the aero-hydro-mooring system is developed, and the results of the motion response are compared with the OC3-Hywind spar. The motion response of the two platforms was simulated in the time-domain with the incident wave period varied in the range of 5~22 s. The exciting wave force with added mass and radiation damping of the spar with the porous shell is compared with the OC3-Hywind spar. The results demonstrate that the motion response amplitude of the spar with the porous shell decreases in all three main motion freedoms (i.e., surge, heave and pitch, etc.), among which the heave motions are most significantly attenuated. The study shows that the coupling of porous shells with a floating platform to achieve the reduced motion responses is feasible and can be an innovative structure for the development of deep-sea offshore floating wind turbines.

Monopiles are commonly utilized in offshore wind farms but are prone to non-linear wave loads and run-ups, significantly affecting their engineering design. Therefore, it is crucial to pursue a complete understanding of the non-linear wave action on monopile foundations. Both numerical and experimental investigations on the non-linear wave loads and run-ups on an offshore wind turbine monopile foundation are performed in this paper. The experiment is carried out at a scale of 1/30 in a wave flume at the State Key Laboratory of Coastal and Offshore Engineering, Dalian University of Technology, in which the wave loads and run-ups along the monopile are measured. Based on the second-order potential flow model and time-domain higher-order boundary element method (HOBEM), the related numerical tests are conducted to study the non-linear effects further. It is found that the present non-linear potential theory is sufficient for the simulation of wave force and run-ups on the monopile in the range of wave slope kA < 0.15 before wave breaking. “W” type distribution of wave run-up along the monopile is found, in which the peak value occurs at the frontward side (i.e., θ =180°) and is the maximum due to full reflection; the two symmetrical minimum amplitudes lie in the zones of (45° ≤ θ ≤ 90°) and (270° ≤ θ ≤ 315°), whose positions shift downward with the increase of wave non-linearity. Energy transfer among the fundamental wave component and higher-order components is also found, which is most apparent on the backward side. Besides, the transverse resonance occurs in the wave flume due to the wavelength being near the flume width, which induces the wave run-up at the backward position larger than that at the frontward position.

As offshore wind development moves toward deeper waters, floating offshore wind turbines have become essential for carbon-neutral energy systems. This study experimentally investigates the hydrodynamic coefficients of typical column–heave-plate components under forced oscillations, focusing on the influence of pitch-induced inclination. A circular column without a heave plate and a circular column equipped with a hexagonal heave plate were tested under heave and surge motions with varying periods, amplitudes, and static inclination angles. The static inclinations were used to represent the attitude variation of platform components during large-amplitude pitch responses. Added mass and damping coefficients were identified using the least squares method. The results show that for the heave-plate-equipped column, increasing the inclination from 0° to 5° and 10° reduced the nondimensional heave added mass by approximately 4.3% and 5.9%, respectively, and reduced the nondimensional heave damping by approximately 7.1% and 6.8%. The corresponding reductions in surge added mass were approximately 5.3% and 10.5%, whereas the reductions in surge damping reached approximately 8.2% and 16.4%, indicating that the surge damping is most sensitive to static inclination. These variations may be associated with the altered geometric projection and disturbed flow symmetry of the inclined component, which may affect the attached-fluid volume and energy-dissipation process during forced oscillation. Future studies should further verify the corresponding local separation and vortex-formation mechanisms through detailed flow-field measurements, PIV, or CFD.

This study investigates the influence of inside-trapped water and remedial grouting on the vertical bearing behaviour of suction bucket foundations in sand through 1 g laboratory model tests. The tests were designed to compare the relative responses of different trapped-water and grouting conditions under the same model scale, sand preparation procedure, and loading protocol. Two target trapped-water conditions were considered: a condition without an observable continuous water layer beneath the bucket lid and a condition with an initial trapped-water thickness of approximately 2 cm. These conditions were controlled and verified before loading using the scale attached to the transparent bucket wall and the underwater camera monitoring system. The results show that inside-trapped water modifies the vertical load-transfer path between the bucket lid and the internal soil plug. When a water layer exists beneath the lid, direct lid–soil plug contact is weakened, and the foundation resistance relies more strongly on skirt-side resistance and the resistance mobilized near the bucket rim. Under cyclic vertical loading, the trapped-water case exhibited larger cumulative displacement and a lower post-cyclic bearing response than the no-trapped-water case. The secant cyclic stiffness showed a continuous increase in the no-trapped-water case, whereas a rise-then-fall trend was observed in the trapped-water case, which may be associated with cyclic densification, soil plug disturbance, changes in lid–soil plug contact, and possible local pore pressure development. Remedial grouting filled the trapped-water space beneath the bucket lid and partially restored the lid–soil plug load-transfer path. Under the present model test conditions, the post-cyclic dimensionless bearing capacity of the grouted cases increased by approximately 13–16% relative to the ungrouted trapped-water case. The grouting cases with different bentonite contents showed similar recovery trends within the limited dataset, suggesting that the improvement was mainly related to filling and sealing the trapped-water space rather than to the intrinsic strength of the grout material.