Antonio Bobet

Dr. Antonio Bobet

orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2009 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
ABAntonio Bobet
Antonio Bobet
AFA. Fakhimi
A. Fakhimi
SJS. Johnson
S. Johnson
JMJoseph Morris
Joseph Morris
FTF. Tonon
F. Tonon
MYM. Ronald Yeung
M. Ronald Yeung
The paper presents a description of the methods used to model rock as discontinuous media. The objective of the work is to bring to the geomechanics community recent advances in numerical modeling in the field of rock mechanics. The following methods are included: (1) the distinct element method; (2) the discontinuous deformation analysis method; and (3) the bonded particle method. A brief description of the fundamental algorithms that apply to each method is included, as well as a simple case to illustrate their use.

1 October 2010 in Rock Mechanics and Rock Engineering
Verified
Journal Article
Closed access
PDF file
ABAntonio Bobet
Antonio Bobet

1 August 2013 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
CMC. S. El Mohtar
C. S. El Mohtar
ABAntonio Bobet
Antonio Bobet
MSM. C. Santagata
M. C. Santagata
VDV. P. Drnevich
V. P. Drnevich
CJCliff T Johnston
Cliff T Johnston
Ottawa sand specimens premixed with 0, 3, and 5% bentonite by dry mass of sand were tested under undrained static and cyclic loading to investigate the effects of bentonite on the static and cyclic shear strength of the sand. The results show that allowing the bentonite to hydrate within the sand pore space increases the cyclic resistance of the sand. For the same skeleton relative density and cyclic stress ratio, cyclic tests on specimens with sufficient hydration times showed a significant increase in the number of cycles required for liquefaction compared with clean sand. When the specimens were allowed an extended postconsolidation aging period, the cyclic resistance increased further. Resonant column and cyclic triaxial tests showed that this is a result of the delay in the generation of excess pore pressure in the presence of the bentonite suspension in the pore space. The improvement in cyclic behavior does not occur at the expense of the static resistance of the soil under working loads be...

1 January 2008 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
MSMarika Santagata
Marika Santagata
ABAntonio Bobet
Antonio Bobet
CJCliff T Johnston
Cliff T Johnston
JHJoonho Hwang
Joonho Hwang
This paper addresses the one-dimensional compression behavior of a highly organic sapric soil in both its natural intact and reconstituted states, based on the results of constant rate of strain and incremental loading oedometer tests. The soil investigated contains 40–60% organic matter, comprised mainly of highly processed humic substances, and represents a “transitional” material between inorganic clays and peats. The inorganic portion is entirely finer than 0.075 mm , with over 60% in the clay fraction (<2 μm) , which XRD analyses indicate contains smectite and vermiculite. Testing of the soil in its intact state relies on high quality block samples and shows that the natural intact soil displays intermediate behavior between that typical of inorganic soft clays and that observed in peats, in terms of compressibility, hydraulic conductivity, and change in hydraulic conductivity with void ratio. As in the case of peats, the coefficient of consolidation is observed to decrease with increasing stress lev...

13 August 2014 in Geophysics
Verified
Journal Article
Closed access
MCMin-Kwang Choi
Min-Kwang Choi
ABAntonio Bobet
Antonio Bobet
LPLaura J. Pyrak-Nolte
Laura J. Pyrak-Nolte
The characterization of fractures using elastic waves requires a parameter that captures the physical properties of a fracture. Many theoretical and numerical approaches for wave propagation in fractured media use normal and shear fracture specific stiffness to represent the complexity of fracture topology as it deforms under stress. Most effective medium approaches assume that the normal and shear fracture specific stiffness are equal, yielding a shear-to-normal specific stiffness ratio of one. Yet several experimental studies show that this ratio can vary from zero to three. We conducted a series of experiments to determine the stiffness ratio for fractures with different surface roughness subjected to mixed-mode loading conditions. Specimens containing a single fracture were subjected to either normal loading or combined normal and shear loading during ultrasonic measurements of transmitted and reflected P- and S-waves. Theoretical analysis based on the displacement discontinuity theory shows, for P- and S-waves with the same wavelength, that the theoretical stiffness ratio is not equal to one, but depends on the ratio of S- to P-wave velocities. The conventional stiffness ratio limit of unity is determined to be appropriate for very smooth fracture surfaces even under mixed-mode loading conditions. However, rough fracture surfaces result in stiffness ratios that are greater than the theoretical limit and the magnitude of the ratio depended on the relative ratio of shear-to-normal stress. The results from the experiments suggest that the conventional practice of assuming a constant stiffness ratio equal to 1.0 may not be appropriate. Therefore, the ratio of shear-to-normal fracture specific stiffness depends on the roughness of the fracture surface and the loading conditions.

11 September 2009 in Rock Mechanics and Rock Engineering
Verified
Journal Article
Closed access
PDF file
ABAntonio Bobet
Antonio Bobet