Titanium-Niobium (TiNb) alloys are commonly employed in a number of implantable devices, yet concerns exist regarding their use in implantology owing to the biomechanical mismatch between the implant and the host tissue. Therefore, to balance the mechanical performance of the load-bearing implant with bone, TiNb alloys with differing porosities were fabricated by powder metallurgy combined with spacer material. Microstructures and phase constituents were characterized with energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The mechanical properties were tested by uniaxial compression, and the corrosion performance was determined via a potentiodynamic polarization experiment. To evaluate a highly matched potential implant with the host, biocompatibilities such as cell viability and proliferation rate, fibronectin adsorption, plasmid-DNA interaction, and an SEM micrograph showing the cell morphology were examined in detail. The results showed that the alloys displayed open and closed pores with a uniform pore size and distribution, which allowed for cell adherence and other cellular activities. The alloys with low porosity displayed compressive strength between 618 MPa and 1295 MPa, while the alloys with high porosity showed significantly lower strength, ranging from 48 MPa to 331 MPa. The biological evaluation of the alloys demonstrated good cell attachment and proliferation rates.
This study aims to produce pure titanium with differing porosity levels for use as a load-bearing implant material that can mimic natural bone structure. Ti + x space holder agent (x: 0, 5, 15, and 20 wt.%) samples were prepared via powder metallurgy route, employing a pressure of 300 MPa followed by sintering at 1200 °C for 6 h. Effect of the space holder agent on the pore characteristics, phase constituent, and mechanical performance, including elastic modulus and ultimate compressive strength, were investigated. Microstructural characterizations were conducted, employing an optical microscope, scanning electron microscopy and energy dispersive spectroscopy. The phase structure was characterized by X-ray diffraction. Additionally, the mechanical behaviour of the samples achieved was assessed by uniaxial compression test at room temperature. The results from the current studies revealed that adding space holder agent effectively modified the porosity level and pore characteristics without altering the phase constituent of the samples. As the space holder agent content was increased from 0 to 20 (wt.%), the porosity level of the samples increased from 18 % to 56 %, while the ultimate compressive strength values reduced significantly from 1,236 MPa to 112 MPa.
The porosity within an implant material is essential for biological activities such as cellular growth and integration with bone tissue. In this regard, implant materials having a porous structure ...
It is crucial to develop multifunctional titanium alloys having optimal mechanical properties, controllable porosity, and high wear resistance. In this study, porous Ti–13Nb–13Zr–xCu ( x : 1, 2, 4, and 8 wt.%) alloys were synthesized via powder metallurgy route to investigate the influence of copper content on pore formation, microstructural features, mechanical behavior, and tribological response. The powder mixtures were compacted at 400 MPa and subsequently sintered at 1300 °C for 2 h. The microstructural features and pore formation were examined by scanning electron microscopy and energy dispersive x-ray spectroscopy (EDS), and x-ray diffraction. The hardness, compressive strength, surface roughness, and wear behavior were evaluated to assess the mechanical and tribological performance of the alloys. The findings revealed that the porosity decreased significantly from approximately 42% to 18% with increasing Cu addition while the ultimate compressive strength increased from 120 ± 4 MPa to 700 ± 11 MPa. Similarly, average hardness increased from 398 HV to 559 HV. The improved mechanical and tribological performances were attributed to enhanced densification, pore refinement, and the formation of Ti 2 Cu intermetallic phases.
26 January 2026 in Adıyaman Üniversitesi Mühendislik Bilimleri Dergisi
Bu çalışmada, farklı soğuk presleme basınçlarının (200, 400 ve 600 MPa) geleneksel toz metalurjisi yöntemiyle üretilen ticari saflıktaki titanyumun mikroyapısal ve mekanik özellikleri üzerindeki etkileri araştırılmıştır. Oda sıcaklığında tek eksenli presleme yöntemiyle farklı basınçlarda kompaktlanan yaş titanyum numuneler, 1400 °C’de 2 saat sinterlenmiştir. Uygulanan presleme basıncının mikroyapıya etkileri; taramalı elektron mikroskobu (SEM), enerji dağılımlı spektroskopi (EDS) ve X-ışını difraksiyonu (XRD) analizleri ile ayrıntılı biçimde incelenmiştir. Ayrıca numunelerin mekanik performansını değerlendirmek amacıyla tek eksenli basma testleri gerçekleştirilmiştir. Elde edilen bulgular, artan soğuk presleme basıncıyla birlikte numunelerdeki gözenek morfolojileri değişmiş olup, gözenek oranları ciddi şekilde düşmüştür. Gözenek oranındaki düşüşe paralel olarak basma dayanımının da arttığı ve 200 MPa, 400 MPa ve 600 MPa soğuk basınç altında preslenen saf Ti malzemelerine ait basma dayanımları; sırasıyla 30 MPa, 160 MPa ve 180 MPa olarak kaydedilmiştir. Sonuç olarak, implant uygulamalarında kullanılabilecek saf titanyum malzemelerde hedeflenen gözenek oranı ve morfolojinin kontrol edilebilmesi açısından soğuk presleme basıncının kritik bir işlem parametresi olduğu ortaya konmuştur.
13 May 2026 in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Bu çalışmada, toz metalurjisi yöntemiyle üretilen gözenekli Ti–Al–Nb esaslı biyomedikal malzemelerin mikroyapısal ve mekanik özellikleri sistematik olarak incelenmiştir. Saf Ti, Ti-3Al-5Nb ve Ti-1Al-10Nb örnekleri, 300 MPa presleme basıncı altında 1300 °C’de 2 saat sinterlenmiştir. Mikroyapısal karakterizasyonlar optik mikroskop, enerji dağılımlı spektroskopi (EDS) ve X-ışını difraksiyonu (XRD) ile gerçekleştirilmiş; mekanik performans ise oda sıcaklığında basma testleriyle değerlendirilmiştir. Elde edilen gözeneklilik oranları sırasıyla %27, %28 ve %26; basma dayanımları ise saf Ti için 358.8 MPa, Ti-3Al-5Nb için 324.8 MPa ve Ti-1Al-10Nb için 314.9 MPa olarak belirlenmiştir. Bulgular, kontrollü gözeneklilik ve uygun faz bileşimi sayesinde Ti–Al–Nb alaşımlarının kemik dokusuyla mekanik uyum sağlayan ve stres kalkanı etkisini minimize eden implant uygulamaları için uygun adaylar olduğunu göstermektedir.