Copper‐oxide compound semiconductors provide a unique possibility to tune the optical and electronic properties from insulating to metallic conduction, from bandgap energies of 2.1 eV to the infrared at 1.40 eV, i.e., right into the middle of the efficiency maximum for solar‐cell applications. Three distinctly different phases, Cu2O, Cu4O3, and CuO, of this binary semiconductor can be prepared by thin‐film deposition techniques, which differ in the oxidation state of copper. Their material properties as far as they are known by experiment or predicted by theory are reviewed. They are supplemented by new experimental results from thin‐film growth and characterization, both will be critically discussed and summarized. With respect to devices the focus is on solar‐cell performances based on Cu2O. It is demonstrated by photoelectron spectroscopy (XPS) that the heterojunction system p‐Cu2O/n‐AlGaN is much more promising for the application as efficient solar cells than that of p‐Cu2O/n‐ZnO heterojunction devices that have been favored up to now.
Erbium-doped fiber amplifiers revolutionized long-haul optical communications and laser technology. Erbium ions could provide a basis for efficient optical amplification in photonic integrated circuits but their use remains impractical as a result of insufficient output power. We demonstrate a photonic integrated circuit–based erbium amplifier reaching 145 milliwatts of output power and more than 30 decibels of small-signal gain—on par with commercial fiber amplifiers and surpassing state-of-the-art III-V heterogeneously integrated semiconductor amplifiers. We apply ion implantation to ultralow–loss silicon nitride (Si 3 N 4 ) photonic integrated circuits, which are able to increase the soliton microcomb output power by 100 times, achieving power requirements for low-noise photonic microwave generation and wavelength-division multiplexing optical communications. Endowing Si 3 N 4 photonic integrated circuits with gain enables the miniaturization of various fiber-based devices such as high–pulse-energy femtosecond mode-locked lasers.
This paper reviews x-ray photoelectron spectroscopy studies on carbon nitride (CN) and reports on results obtained from CN thin films prepared by mass selected ion-beam deposition. The core-level spectra of samples deposited at room temperature show that nitrogen is incorporated into the amorphous network in two different bonding configurations; carbon has three main bonding configurations whose relative contributions vary as a function of the nitrogen content. For samples deposited at elevated temperatures an ordering of the amorphous CN network towards a crystalline graphitelike structure is observed. Furthermore, both deposition at elevated temperatures (350 °C) and post-deposition ion irradiation have a strong influence on the bonding configuration in the CN films. Based on these results and the results reported in the reviewed literature a picture of the microstructure of carbon nitride deposited using energetic species is developed.
Successful ex situ and in situ cleaning procedures for AlN and GaN surfaces have been investigated and achieved. Exposure to HF and HCl solutions produced the lowest coverages of oxygen on AlN and GaN surfaces, respectively. However, significant amounts of residual F and Cl were detected. These halogens tie up dangling bonds at the nitride surfaces hindering reoxidation. The desorption of F required temperatures Remote H plasma exposure was effective for removing halogens and hydrocarbons from the surfaces of both nitrides at but was not efficient for oxide removal. Annealing GaN in at produced atomically clean as well as stoichiometric GaN surfaces.
Zinc oxide (ZnO) nanobelts synthesized by thermal evaporation have been ion implanted with 30 keV ions. Both transmission electron microscopy and photoluminescence investigations show highly defective material directly after the implantation process. Upon annealing to 800 °C, the implanted Mn remains in the ZnO nanobelts and the matrix recovers both in structure and luminescence. The produced high-quality ZnO:Mn nanobelts are potentially useful for spintronics.
Light–matter interactions are inherently slow as the wavelengths of optical and electronic states differ greatly. Surface plasmon polaritons — electromagnetic excitations at metal–dielectric interfaces — have generated significant interest because their spatial scale is decoupled from the vacuum wavelength, promising accelerated light–matter interactions. Although recent reports suggest the possibility of accelerated dynamics in surface plasmon lasers, this remains to be verified. Here, we report the observation of pulses shorter than 800 fs from hybrid plasmonic zinc oxide (ZnO) nanowire lasers. Operating at room temperature, ZnO excitons lie near the surface plasmon frequency in such silver-based plasmonic lasers, leading to accelerated spontaneous recombination, gain switching and gain recovery compared with conventional ZnO nanowire lasers. Surprisingly, the laser dynamics can be as fast as gain thermalization in ZnO, which precludes lasing in the thinnest nanowires (diameter less than 120 nm). The capability to combine surface plasmon localization with ultrafast amplification provides the means for generating extremely intense optical fields, with applications in sensing, nonlinear optical switching, as well as in the physics of strong-field phenomena.