Ethem Furkan HIDIR

Mr. Ethem Furkan HIDIR

Dentistry, Fırat University, Elazığ, Turkey (Türkiye)
orcid

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 July 2026 in Crystals
Verified
Journal Article
Open access
PDF file
EHEthem Furkan HIDIR
Ethem Furkan HIDIR
ASAli Sincar
Ali Sincar
Cevher Kürşat MACİTCevher Kürşat MACİT
Cevher Kürşat MACİT
STSamet Tekin
Samet Tekin
UUUkbe Usame Uçar
Ukbe Usame Uçar
Poly(methyl methacrylate) (PMMA) remains a clinically important denture base polymer because of its favorable processability, aesthetics, repairability and long-term prosthodontic use; however, its limited surface hardness and susceptibility to sliding-induced degradation constrain surface durability. This study establishes the structure–chemistry–microstructure–tribology relationships and composition-window predictive behavior of heat-polymerized PMMA reinforced with titanium diboride (TiB2). PMMA/TiB2 composites containing 1, 3 and 5 wt.% TiB2 were prepared and compared with unreinforced PMMA. X-ray diffraction confirmed preservation of the broad amorphous/semi-amorphous PMMA response, while TiB2-related crystalline features became increasingly detectable with reinforcement content. ATR-FTIR showed retention of the characteristic C–H, ester C=O and C–O/C–O–C vibrations. SEM/EDS demonstrated progressively greater particle-related surface contrast and local Ti/B-associated elemental signatures. Vickers microhardness increased from 20.0 ± 0.7 to 35.0 ± 1.39 HV0.03, corresponding to a 75.0% improvement at 5 wt.% TiB2. After 1000 m of dry sliding, total mass loss decreased from 32.4 ± 0.5 to 14.9 ± 0.4 mg (54.0% reduction), overall coefficient of friction decreased from 0.58 to 0.35, and representative wear-track width decreased from 481.4 to 101.8 µm. A parsimonious distance–composition interaction model retained strong grouped leave-one-composition-out performance for cumulative wear (R2 = 0.9622; RMSE = 1.53 mg), while a linear composition model provided the most robust hardness prediction (R2 = 0.9317; RMSE = 1.50 HV0.03). More complex nonlinear models did not improve prediction for held-out compositions. Within the investigated 0–5 wt.% window, 5 wt.% TiB2 provided the most effective combination of matrix preservation, surface hardening, wear suppression and frictional stabilization.
1

22 August 2026 in Crystals
Verified
Journal Article
Open access
PDF file
ASAli Sincar
Ali Sincar
EHEthem Furkan HIDIR
Ethem Furkan HIDIR
Cevher Kürşat MACİTCevher Kürşat MACİT
Cevher Kürşat MACİT
STSamet Tekin
Samet Tekin
UUUkbe Usame Uçar
Ukbe Usame Uçar
FOFatih Osmanlıoğlu
Fatih Osmanlıoğlu
Heat-polymerized poly(methyl methacrylate) (PMMA) is widely used for denture bases but remains susceptible to surface deformation and sliding wear. This study evaluated the structure, chemistry, surface morphology, microhardness, and dry-sliding tribology of PMMA reinforced with 1, 3, and 5 wt.% cubic boron nitride (c-BN). Disk specimens (10 mm diameter × 2 mm thickness) were prepared; ten specimens per group were tested for Vickers microhardness and wear/coefficient of friction, while one representative specimen per group was examined by XRD, ATR-FTIR, and SEM/EDS before and after wear. The PMMA amorphous/semi-amorphous response and characteristic ester bands were retained, whereas c-BN-related diffraction features and B/N signals became more evident with reinforcement. Microhardness increased from 20.00 ± 0.70 to 45.00 ± 1.61 HV0.03. After 1000 m at 10 N and 1 m s−1, mass loss decreased from 32.4 to 9.8 mg and the overall coefficient of friction from 0.58 to 0.28. Post-wear SEM/EDS showed reduced grooving, smearing, and material detachment at higher c-BN contents. Statistical analysis confirmed large composition effects, and composition-window models reproduced the measured hardness and wear trends. Within the tested range, 5 wt.% c-BN provided the strongest surface-hardening and wear-suppression response under controlled dry-sliding conditions.