Vehicle electrification is envisioned to be a significant component of the forthcoming smart grid. In this paper, a smart grid vision of the electric vehicles for the next 30 years and beyond is presented from six perspectives pertinent to intelligent transportation systems: 1) vehicles; 2) infrastructure; 3) travelers; 4) systems, operations, and scenarios; 5) communications; and 6) social, economic, and political.
7 October 2008 in IEEE Transactions on Industrial Electronics
Bilateral control systems are strongly required to apply to endoscopic surgeries. It is necessary that the system has enough degrees of freedom for applying various operation procedures including endoscopic surgery. When the degrees of freedom of the system are increased, the amount of control calculation is also increased, and it is hard to keep sampling periods short. The bilateral control systems, however, require comparatively shorter sampling periods, particularly the control system based on an acceleration control system. Hence, it is a difficult issue to increase the degrees of freedom of the bilateral control system. In this paper, the sampling period is kept short in the multidegree of freedom system by using field programmable gate arrays as processors. The bilateral control system based on the acceleration control system is implemented in a robot system, which has 12 DOF, and some experimental results are shown, and the errors between the response of the master and slave robots are discussed.
22 November 2004 in IEEE Transactions on Industrial Electronics
The purpose of this study is to control multiple mobile robots in formation considering the ability of a robot using the "Leader-Following" strategy. There are three features of this study. First, a performance index that shows mobile robot ability is quantified. Specifically, maximum acceleration and maximum velocity of a robot are defined by maximum admissible rotation and maximum continuous torque of a motor. The performance index is quantified from arrival time on the destination using these parameters. Second, a new controller is proposed based on the performance index, so that robots can be controlled according to robot ability. Third, a compliance controller using a virtual repulsion is suggested in this paper, so that each robot can avoid collision. Finally, simulation and experiments are done in a real-time system using RT-Messenger. RT-Messenger allows robots to transmit information regarding their positions to each other in real time. These results shows the validity of the proposed method.
9 July 2007 in IEEE Transactions on Industrial Electronics
Bilateral teleoperation has been needed in many areas, such as space activities, work on an atomic power plant, minimally invasive surgery, etc. In bilateral teleoperation, transfer of keen tactile sense, which is as if the operator directly touches the environment, is required. Sensing of wide-frequency-bandwidth force information is required in achieving the transferring of a keen tactile sensation. A bilateral controller based on acceleration control with disturbance observers is available to achieve transfer of a keen tactile sensation. In this bilateral controller, the frequency bandwidth of sensed force is determined by the cutoff frequency of a low-pass filter used in the disturbance observer. The cutoff frequency is in inverse proportion to a sampling period. Therefore, shortening of the sampling period improves performance of bilateral teleoperation. In this paper, a bilateral-teleoperation system using a field-programmable gate array (FPGA) is introduced. The FPGA is an large scale integration where a user can design its internal logic. When the motion controller is implemented on an FPGA, it operates faster than that implemented in a personal computer with a real-time operating system. The sampling period is shortened from 100 to 10 mus by using an FPGA. The implemented controller is evaluated by experiments.
30 April 2007 in IEEE Industrial Electronics Magazine
This paper describes a collision avoidance method for a biped robot with an upper body. We propose a method wherein the robot stops in front of an obstacle by generating arm force. When the robot detects the obstacle by the arm tip, it should stop short of the obstacle to avoid crash. Hence, we propose trajectory planning in consideration of the pushing force of the arm. The arm force is controlled to be generated as a function of the distance from the robot body to the obstacle. The closer the robot approaches the obstacle, the larger the arm force becomes. As a result, the robot can stop by utilizing the arm force. In case the obstacle is unmovable, the robot can stop by exerting arm force. If it is movable, the robot can continue walking by pushing it. In this paper, the linear inverted pendulum mode (LIPM) and the idea of orbital energy are introduced, and then, we extend LIPM and orbital energy in consideration of the dynamics of the arm force. The extended orbital energy is utilized to discriminate whether the robot can stop or not and to modify the trajectory of the robot to avoid collision
For rich network services, it is indispensable to reconstruct TCP stream in the middle of the network. In this reconstruction function, managing a large number of streams is a crucial as an embedded hardware for achieving high-throughput processing. In this case, hashing is a well-used solution as an ID key of TCP streams. Since CRC hashes have simple tree structure of XOR logics and are perfectly composed of combination logics, they can easily be hardware implemented and enables low-latency calculation of the hash values. Therefore, CRC hash has been used in network applications where low-latency and high speed operations are necessary. Some of their usages include data identification, load balancing, encryption, and checksum. Although CRC hashes may be well suited for hardware implementation, it is not the top choice when collision rates and distribution of hash values are considered. For some network workloads, CRC hashing shows very uneven distribution of hash values and can lead to decrease in the overall performance of network systems. In this study, two hashes, Jenkins hash and MurmurHash, are implemented on a FPGA as TCP connection manager and evaluated for their aptitude for hashing used in hardware-based network applications.