Engineered fluid HFE-7100 is an outstanding detergent and coolant with excellent thermal and chemical stability. Electrohydrodynamic jet disintegration and subsequent droplet formation of HFE-7100 dielectric liquid mixed with ethanol were experimentally investigated in this study. Contact-type charging was employed with the capillary nozzle directly connected to a negative high-voltage power supply, while the counter electrode was grounded. High-speed photography was utilized to capture the liquid breakup and droplet formation behaviors. The results showed that an ethanol content of 8% by volume visibly improved the charging performance of HFE-7100 due to the increase in the liquid electrical conductivity. In addition, with the increase in the applied voltage, the jet breakup was found to transform from the dripping/jetting mode to the ramified mode, which is characterized by a steady liquid sheet with fine droplets forming at the edge. Two distinct ramified breakup configurations, called the pudgy-ramified and lanky-ramified modes, are proposed, and their detailed structural parameters and droplet size distributions are discussed. The diameters of the droplets produced under the permanent ramified configuration could be as small as a few micrometers. Finally, a jet breakup regime map based on the Reynolds number Re and electric bond number BoE was established. Overall, the electrospray technique has shown promise for spray cooling enhancement, and the main results of this paper may be useful for the development of electrospray cooling with a dielectric coolant.
When a fluid is subject to an electric field, it usually processes unique features compared to the conventional fluid that arises from coupling between charged particles and fluid interface. Based on this commonality, we defined the concept of “charged multiphase flow” and constructed a generalized charged multiphase flow system using the “Tai Chi Diagram” to analyze the properties and features of different study objects, with an emphasis on the bubble dynamics on the charged liquid–gas flow object, covering the processes of bubble generation, motion, and interaction, as well as the important dynamic behaviors, involved such as bubble deformation, coalescence, and breakup. Furthermore, in light of the special plasma–liquid interface phenomenon formed by the ionization of the gas/vapor phase in the liquid phase in strong electric fields, the traditional gas–liquid–solid three-phase flow system is expanded into a broader range of multiphase flow systems involving plasma, which enriches the theoretical and frontier scientific problems of the multiphase flow. In addition, technical innovations, remaining work, and future trends in the development of the charged liquid–gas flow, and their potential applications are discussed.
Impact behaviors of an electrically charged water droplet on different solid substrates and subsequent dynamic mechanisms were experimentally investigated in this study. Droplets were generated from a metal capillary by a syringe pump with a constant diameter of about 2.2 mm. The capillary was directly connected to a high voltage direct current power supply, while a lower counter ring electrode was grounded. A high-speed camera was utilized to visualize the droplet impact morphology. The influences of the droplet charge density, substrate wettability, and surface temperature were analyzed. The results showed that the impact on hydrophilic surfaces exhibited a greater spreading diameter but a smaller recoiling height than that on a hydrophobic surface, which was attributed to the increased viscous dissipation on the substrate. In addition, compared with a neutral droplet, the maximum spreading diameter of a charged droplet was found to be improved by about 8.4%, where the enhancing effects were proportional to the droplet charge ratio. This was due to the weakening effects of the Coulomb repulsion on the liquid surface tension. Moreover, the impact of charged droplets on a hot copper substrate in three different boiling regimes, called convection, nucleate and film boiling, was also discussed. Finally, a model of the maximum spreading ratio of a charged droplet based on the Weber number, charge ratio, and wettability was established. This study demonstrated that the free charges in a droplet was able to influence its impact behaviors, which would hold great promise for some related technologies.
18 May 2024 in International Journal of Heat and Mass Transfer
Droplet impact on a hot substrate under an electric field is fundamental and crucial for electrospray cooling. However, the involved thermal–electric coupling impact electrohydrodynamic has not been well understood. In this study, the effects of an electric field on the droplet impact behavior in different thermal regimes and the subsequent dynamic mechanisms were experimentally investigated. The results showed that the vertical electric field would result in an upward liquid ejection in the film evaporation regime. In the nucleate boiling regime, the liquid pinch-off phenomenon was observed. In addition, the droplet evaporation rate was increased by approximately 23% with an electric field of 6 kV/cm. In the film boiling regime, both the residence time and bounce-off droplet height were significantly increased. The various impact phenomena were mainly explained by the competition between electrostatic and capillary pressures. The comprehensive effects of surface free charges and temperature variation on the droplet surface tension coefficient were discussed. Moreover, according to the thermal analysis, the heat transfer in the film boiling regime with an electric field was enhanced by approximately 137%. This work contributed to the development of the droplet impact dynamics under the coupling temperature and electric fields and demonstrated great promise for the electric field for thermal-fluid manipulation.