Transformation of Al(NO3)3∙9H2O (upon heating in the range of 20–1200 °C) into blends of amorphous and crystalline boehmite (210–525 °C), amorphous alumina and crystalline γ-Al2O3 (850 °C), and crystalline α-Al2O3 (1100 °C) was analyzed using X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), infrared (IR) spectroscopy, thermogravimetry, and low-temperature nitrogen adsorption. Boehmite consists of nanoparticles of 6–10 nm in diameter, and part of them has crystalline structure observed in HRTEM images, despite they are XRD amorphous. The nanoglobules are surrounded by amorphous aluminum hydroxide with chains of –AlO(H)–O–AlO(H)– of 1–5 nm in length. Heating of samples at 350–525 °C gives mesoporous aluminum hydroxide with a relatively narrow pore size distribution. An increase in calcination temperature to 850 °C decreases the porosity of alumina composed of amorphous and crystalline (γ-Al2O3) phases. Calcination at 1100 °C gives α-Al2O3 with strongly decreased porosity of aggregates.
The article investigates the effect of thermal modification of porous carbon material (PCM), obtained from plant feedstock, on its morphology and fractal structure by small-angle X-ray scattering (SAXS) method. The analysis of the scattering intensity curves serve the basis for calculating the parameters of the PCM porous structure: the Porod constant, the Porod invariant, average pore radius, specific surface area, and mass and surface fractal dimensions. It has been found out that the PCMs obtained have fractal structure, formed from mass and surface fractals, the sizes of which increase at the growth of temperature and modification time. PACS 81.05.Uw; 61.05.cf; 82.47.Aa
The results of electrochemical studies of nanoporous carbon as electrode material for electrochemical capacitors (EC) are presented in this work. Nanoporous carbon material (NCM) was obtained from the raw materials of plant origin by carbonization and subsequent activation in potassium hydroxide. It is established that there is an optimal ratio of 1:1 between content of KOH and carbon material at chemical activation, while the maximum specific capacity of NCM is 180 F/g. An equivalent electrical circuit, which allows modeling of the impedance spectra in the frequency range of 10−2 to 105 Hz, is proposed, and a physical interpretation of each element of the electrical circuit is presented.
15 February 2022 in Physics and Chemistry of Solid State
The paper presents a simple one-step "green" approach to the synthesis of magnetite nanoparticles. The magnetite nanoparticles were synthesized using fruit extract obtained from grape peels and grape pulp. The formation of magnetite nanoparticles was confirmed by X-ray diffraction analysis (XRD), infrared spectroscopy (IR), Mössbauer spectroscopy, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The crystallites sizes of magnetite nanoparticles are 7 and 14 nm for Fe3O4-peel and Fe3O4-pulp samples, respectively. Scanning electron microscopy images show that the samples consist of agglomerated nanoparticles. The synthesized magnetite nanoparticles showed good prospects for their use in magnetic hyperthermia. SAR values of 0.488 W/g and 1.330 W/g for Fe3O4-peel and Fe3O4-pulp samples, respectively. The synthesized magnetic nanoparticles show excellent colloidal stability in the aqueous solutions. The maximum hyperthermia temperatures are 42.28 °C and 42.48 °C for Fe3O4-peel and Fe3O4-pulp samples, respectively. Studies of the catalytic activity of magnetite were performed in decomposition of hydrogen peroxide in a batch mode. The degrees of H2O2 decomposition are 67.5% and 65.25% for the Fe3O4-peel and Fe3O4-pulp samples respectively. The high catalytic activity of the synthesized samples makes them promising candidates for the decomposition of hydrogen peroxide in wastewater disinfection.