Speeding reactions through ionic strength: Brønsted acidity is introduced into microporous zeolites through the addition of framework aluminum. Pfriem et al. show that in the presence of water, the limited volume in the microchannels of zeolite H-MFI leads to a high concentration of hydrated hydronium ions at aluminum sites. The resulting high charge density creates a highly non-ideal solvation environment and, for cyclohexanol dehydrogenation, the charged carbenium-ion transition state was stabilized. A higher rate was maintained with lower-acidity sodium ion–exchanged zeolites that had the same high ionic strength. Science , abh3418, this issue p. 952
Mechanistic aspects of deconstruction and hydrodeoxygenation of organosolv lignin using zeolite (HZSM-5 and HBEA) and SiO2 supported Ni catalysts are reported. Lignin was deconstructed and converted to substituted alicyclic and aromatic hydrocarbons with 5 to 14 carbon atoms. Full conversion with total yield of 70 ± 5 wt% hydrocarbons was achieved at 593 K and 20 bar H2. The organosolv lignin used consists of seven to eight monolignol subunits and has an average molecular weight of ca. 1200 g mol−1. The monolignols were mainly guaiacyl, syringyl and phenylcoumaran, randomly interconnected through β-O-4, 4-O-5, β-1, 5-5′ and β–β ether bonds. In situ IR spectroscopy was used to follow the changes in lignin constituents during reaction. The reductive catalytic deconstruction of organosolv lignin starts with the hydrogenolysis of aryl alkyl ether bonds, followed by hydrogenation of the aromatic rings to cyclic alcohols. Oxygen is removed from the alcohols via dehydration on Brønsted acid sites to cyclic alkenes that are further hydrogenated.
Hydrogen transfer reactions have exceptional importance, due to their applicability in numerous synthetic pathways, with academic as well as industrial relevance. The most important transformations are, e.g., reduction, ring-closing, stereoselective reactions, and the synthesis of heterocycles. The present review provides insights into the hydrogen transfer reactions in the condensed phase in the presence of noble metals (Rh, Ru, Pd) as catalysts. Since the H-donor molecules (such as alcohols/ethers and amines (1°, 2°, 3°)) and the acceptor molecules (alkenes (C=C), alkynes (C≡C), and carbonyl (C=O) compounds) play a crucial role from mechanistic viewpoints, the present summary points out the key mechanistic differences with the interpretation of current contributions and the corresponding historical achievements as well.
In this Review, all known chemical methods for the conversion of renewable resources into benzenoid aromatics are summarized. The raw materials that were taken into consideration are CO2; lignocellulose and its constituents cellulose, hemicellulose, and lignin; carbohydrates, mostly glucose, fructose, and xylose; chitin; fats and oils; terpenes; and materials that are easily obtained via fermentation, such as biogas, bioethanol, acetone, and many more. There are roughly two directions. One much used method is catalytic fast pyrolysis carried out at high temperatures (between 300 and 700 °C depending on the raw material), which leads to the formation of biochar; gases, such as CO, CO2, H2, and CH4; and an oil which is a mixture of hydrocarbons, mostly aromatics. The carbon selectivities of this method can be reasonably high when defined small molecules such as methanol or hexane are used but are rather low when highly oxygenated compounds such as lignocellulose are used. The other direction is largely based on the multistep conversion of platform chemicals obtained from lignocellulose, cellulose, or sugars and a limited number of fats and terpenes. Much research has focused on furan compounds such as furfural, 5-hydroxymethylfurfural, and 5-chloromethylfurfural. The conversion of lignocellulose to xylene via 5-chloromethylfurfural and dimethylfuran has led to the construction of two large-scale plants, one of which has been operational since 2023.