In this paper, we propose two designs of slot-fed metasurface antenna for beam steering applications. Both designs have the same two-layer stacked configuration consisting of either a single-slot or a double-slot radiator, and a metasurface superstrate. In contrast to existing phase-gradient metasurfaces with varying unit elements for beam steering, our proposed metasurface is formed by uniform square rings. At operating frequencies, each square ring acts as an individual resonating element. By exciting the elements in sequence with different phase delays through the slot radiator, the generated antenna beam can be steered. In the first design, the position of the single-slot radiator is shifted to achieve the beam steering functionality; while for the second antenna, to avoid mechanically moving the feeding slot, a double-slot-feeding structure is proposed with two slots excited with varying phase differences. Simulation and experimental results show that beam steering angles of -35 to 35 degrees can be achieved for the single-slot-feeding design, and -30 to 30 degrees are realizable for the double-slot-feeding configuration. Comparing with conventional phased array antennas, our proposed designs have compact size with moderate to high antenna gain.
28 January 2019 in International Journal of Antennas and Propagation
In this paper, we propose a reconfigurable metasurface antenna for beam switching applications. The reconfigurable metasurface is formed by uniformly distributed double-split square rings loaded with positive-intrinsic-negative (PIN) diodes for dual operations of a wave reflector and a wave director. Specifically, when the PIN diodes are forward biased, an epsilon-negative (ENG) metasurface is realized which reflects all incident waves with appropriate polarization; when the diodes are reverse biased, at the same operating frequency, a mu-near-zero (MNZ) metasurface is acquired which directs wave propagation. For excitation, a dipole radiator loaded with the same type of PIN diode is designed. Simulation and measurement results show good agreement and verify the beam switching functionality of the proposed metasurface antenna.
25 January 2022 in IEEE Transactions on Power Electronics
A dynamic wireless power transfer (DWPT) system using the conventional magnetoinductive (MI) waveguide suffers from periodic power nulls resulting from standing waves. Although numerous methods have been developed to mitigate the nulls, additional active circuitry was required, increasing the complexity. In this article, the MI waveguide with alternate magnetic coupling polarities between successive resonator cells is proposed for a true nulls-free DWPT system with no use of active components. Two configurations of the alternately coupled MI (ACMI) waveguide are developed—one with the incorporation of a quadrature-phase termination for a linear waveguide, and the other with the adoption of a circular waveguide. Extensive analysis of the generalized ACMI waveguide is provided, and the developed configurations are theoretically verified to maintain power transfer efficiency, independent of the free-positioned load. Practical implementation of DWPT systems using the linear and circular ACMI configurations with seven resonator cells at 13.56-MHz operation are experimentally demonstrated to exhibit no power transfer nulls and achieve up to fivefold reduction in efficiency variation, as compared to their MI counterparts. Comparisons with theoretical calculation are given for verification of the analysis integrity. An experimental model of a batteryless DWPT system is also demonstrated using the circular waveguide as accompanied by a video.
In this paper, we apply a relativistic finite-difference time-domain (FDTD) method by using the Lorentz transformation to analyze metamaterials moving at a high speed. As an example, we consider a slab of left-handed metmaterial (LHM) with both relative permittivity and permeability equal to −1. Simulation results show that when the LHM slab moves at a high speed, its electromagnetic responses are drastically different from the static case. Specifically, when the LHM slab moves toward the source, for the case of normal incidence, there exists a special velocity at which fields experience a zero spatial phase delay through the LHM slab; while for the oblique incidence, above a certain velocity fields inside the LHM become evanescent. On the other hand, when the LHM slab moves away from the source, for the case of normal incidence, at the same special velocity the magnitudes of both electric and magnetic fields inside the LHM slab reach their minimum values; for the oblique incidence, the slab functions as a field converter. Besides, the transmitted waves through the LHM slab experience a red-shift (to a lower frequency) and the shift is proportional to the velocity of the LHM slab regardless of the moving direction.
2 July 2020 in International Journal of RF and Microwave Computer-Aided Engineering
This paper proposes a cost-effective design approach for metasurface-enabled microstrip antennas optimized for the dual-band of mmWave 5G frequencies, specifically 26 GHz (n258) and 28 GHz (n257). The proposed antennas are based on metasurface and are manufactured using standard printed circuit board (PCB) processes on a low-cost FR-4 substrate, making them suitable for mass production at an affordable price. The dimensions of the proposed antenna are $25\times 25\times 7.6 \ \text{mm}^{3}$ . It demonstrates a $\vert \mathbf{S}_{11}\vert \leq-10\boldsymbol{\text{dB}}$ bandwidth of 31.9% (23.2-32.0 GHz) and offers a higher gain of 7.2 dB compared to a non-metasurface patch antenna with a gain of 5.12 dBi. The proposed antenna achieves a peak gain of 13.8 dBi and maintains a good front-to-back ratio exceeding 15 dB across the entire operating band. Moreover, the use of low-cost FR-4 substrate and PCB fabrication processes ensures cost-effectiveness, making these antennas highly suitable for cost-efficient deployment in 5G applications.