Sensing services for the detection of humans and animals by analyzing the environmental changes of wireless local area network (WLAN) signals have attracted attention in recent years. In object detection using WLAN signals, a widely known technique is the use of time changes in received signal strength indicators that are easily measured between WLAN devices. Utilizing channel response, including power and phase values per subcarrier on multiple input multiple output (MIMO), the orthogonal frequency division multiplexing transmission was researched as channel state information (CSI) to further improve detection accuracy. This paper describes a WLAN-based CSI monitoring system that efficiently acquires the CSI of multiple links in a target area where multiple CSI measuring stations are distributed. In the system, a novel CSI monitoring station captures wireless packets sent within the area and extracts CSI by analyzing the packets on the sounding protocol, specified by IEEE 802.11ac. The paper also describes the system configuration and shows that indoor experimental measurements confirmed the system’s feasibility.
A bathroom has higher probability of accidents than other rooms due to a slippery floor and temperature change. Because of high privacy and humidity, we face difficulties in monitoring inside a bathroom using traditional healthcare methods based on cameras and wearable sensors. In this paper, we present a danger-pose detection system using commodity Wi-Fi devices, which can be applied to bathroom monitoring, preserving privacy. A machine learning-based detection method usually requires data collected in target situations, which is difficult in detection-of-danger situations. We therefore employ a machine learning-based anomaly-detection method that requires a small amount of data in anomaly conditions, minimizing the required training data collected in dangerous conditions. We first derive the amplitude and phase shift from Wi-Fi channel state information (CSI) to extract low-frequency components that are related to human activities. We then separately extract static and dynamic features from the CSI changes in time. Finally, the static and dynamic features are fed into a one-class support vector machine (SVM), which is used as an anomaly-detection method, to classify whether a user is not in bathtub, bathing safely, or in dangerous conditions. We conducted experimental evaluations and demonstrated that our danger-pose detection system achieved a high detection performance in a non-line-of-sight (NLOS) scenario.
In the ITS (intelligent transportation system), vehicle detection is one of the core technologies. We are developing an acoustic vehicle detector that detects vehicles using a sound map, which is a map of sound arrival time difference on two microphones. We developed vehicle detection algorithms based on state machine and DTW (dynamic time warping) to detect S-curves on a sound map drawn by passing vehicles. However, the detection algorithms often fail to detect simultaneous and sequential passing vehicles. This paper presents SAVeD, a sequential acoustic vehicle detector. The SAVeD fits an S-curve model to sound map points using a RANSAC (random sample consensus) robust estimation method to detect each vehicle. The SAVeD then removes sound map points corresponding to the detected vehicle and continues vehicle detection process for the following vehicles. Experimental evaluations demonstrated that the SAVeD improves detection accuracy by more than 10 points compared to the state-machine based algorithm.
The deployment of a large-scale indoor sensor network faces a sensor localization problem because we need to manually locate significantly large numbers of sensors when Global Positioning System (GPS) is unavailable in an indoor environment. Fingerprinting localization is a popular indoor localization method relying on the received signal strength (RSS) of radio signals, which helps to solve the sensor localization problem. However, fingerprinting suffers from low accuracy because of an RSS instability, particularly in sensor localization, owing to low-power ZigBee modules used on sensor nodes. In this paper, we present MuCHLoc, a fingerprinting sensor localization system that improves the localization accuracy by utilizing channel diversity. The key idea of MuCHLoc is the extraction of channel diversity from the RSS of Wi-Fi access points (APs) measured on multiple ZigBee channels through fingerprinting localization. MuCHLoc overcomes the RSS instability by increasing the dimensions of the fingerprints using channel diversity. We conducted experiments collecting the RSS of Wi-Fi APs in a practical environment while switching the ZigBee channels, and evaluated the localization accuracy. The evaluations revealed that MuCHLoc improves the localization accuracy by approximately 15% compared to localization using a single channel. We also showed that MuCHLoc is effective in a dynamic radio environment where the radio propagation channel is unstable from the movement of objects including humans.
Excessive power consumption is a major problem in wireless communication. This is particularly true in ubiquitous computing environments, since wireless devices consume a considerable amount of energy in idle listening. Wake-up wireless communication technology is a promising candidate for reducing power consumption during idle listening. To realize wake-up wireless communication, this paper proposes a novel ID matching mechanism that uses a Bloom filter. This paper describes the design and implementation of a wireless wake-up module that uses this ID matching mechanism. Simulation results reveal that the wake-up module consumes only 12.4 muW while idle listening, and that employing this Bloom-filter-based approach eliminates 99.95 % of power consumption in our application scenarios.
BLE (Bluetooth Low Energy) based localization is a next candidate for indoor localization. In this paper, we propose a new BLE-based fingerprinting localization scheme that improves localization accuracy. BLE is a narrow band communication that is highly affected by frequency selective fading and channel gains. We employ channel-specific features to location fingerprint to improve localization accuracy. Current BLE standards provide no API to retrieve an advertising channel number. We therefore developed a separate channel advertising scheme to measure RSS (Received Signal Strength) on each advertising channel. To demonstrate the feasibility of the separate channel fingerprinting, we conducted initial evaluations. Experimental evaluations showed that the separate channel fingerprinting improves accuracy by approximately 12%.