This paper presents a static test rig called “Octopus” designed for the validation of numerical models aimed at calculating the nonlinear dynamic response of a bladed disk with underplatform dampers (UPDs). The test rig supports a bladed disk on a fixture and each UPD is pressed against the blade platforms by wires pulled by dead weights. Both excitation system and response measurement system are noncontacting. This paper features the design and the setup of the noncontacting excitation generated by electromagnets placed under each blade. A traveling wave excitation is generated according to a desired engine order by shifting the phase of the harmonic force of one electromagnet with respect to the contiguous exciters. Since the friction phenomenon generated by UPDs introduces nonlinearities on the forced response, the amplitude of the exciting force must be kept constant at a known value on every blade during step-sine test to calculate frequency response functions. The issue of the force control is therefore addressed since the performance of the electromagnet changes with frequency. The system calibration procedure and the estimated errors on the generated force are also presented. Examples of experimental tests that can be performed on a dummy integral bladed disk (blisk) mounted on the rig are described in the end.
A joint between two components can be seen as a means to transmit dynamic information from one side to the other. To identify the joint, a reverse process called decoupling can be applied. This is not as straightforward as the coupling, especially when the substructures have three-dimensional characteristics, or sensor mounting effects are significant, or the interface degrees-of-freedom (DoF) are inaccessible for response measurement and excitation. Acquiring frequency response functions (FRFs) at the interface DoF, therefore, becomes challenging. Consequently, one has to consider hybrid or expansion methods that can expand the observed dynamics on accessible DoF to inaccessible DoF. In this work, we attempt to identify the joint dynamics using the system equivalent model mixing (SEMM) decoupling method with a virtual point description of the interface. Measurements are made only at the internal DoF of the uncoupled substructures and also of the coupled structure assuming that the joint dynamics are observable in the assembled state. Expanding them to the interface DoF and performing coupling and decoupling operations iteratively, the joint is identified. The substructures under consideration are a disk and blade—an academic test geometry that has a total of 18 blades but only one blade-to-disk joint is considered in this investigation. The joint is a typical dove-tail assembly. The method is shown to identify the joint without any direct interface DoF measurement.
30 November 2009 in Machining Science and Technology
Results of X-ray residual stress measurements on Inconel 718 turbine shaft samples are here proposed. The paper presents part of the EU STREP project VERDI activity, where the aim was to supply those who numerically simulate machining process with an experimental database of proved reliability. Measurements were planned on a set of samples machined with different levels of cutting speed and feed rate. Due attention was given to the assessment of the uncertainty of experimental results. A database of surface residual stress values and depth profiles is presented with the estimated uncertainty both on stress and depth values. The stress proved to be always tensile at the surface and compressive below the surface. Higher cutting speed and feed rates produce higher surface tensile stresses but the trends are different for the two measurement directions.
The present paper is focused on the post processing of the data coming from the Blade Tip-Timing (BTT) sensors in the case where two very close peaks are present in the frequency response of the vibrating system. This type of dynamic response with two very close peaks can occur quite often in bladed disks. It is related to the fact that the bladed disk is not perfectly cyclic symmetric and the so called “mistuning” is present. A method based on the fitting of the BTT sensors data by means of a 2 degrees of freedom (2DOF) dynamic model is proposed. Nonlinear least square optimization technique is employed for identification of the vibration characteristics. A numerical test case based on a lump parameter model of a bladed disk assembly is used to simulate different response curves and the corresponding sensors signals. The Frequency Response Function (FRF) constructed at the resonance region is compared with the traditional Sine fitting results, the resonance frequencies and damping values estimated by the fitting procedure are also reported. Accurate predictions are achieved and the results demonstrate the considerable capacity of the 2DOF method to be used as a standalone or as a complement to the standard Sine fitting method.