In the past few years, lead halide perovskite solar cell power conversion efficiencies have risen by using a wide variety of fabrication methods and just passed 20%. Perovskite solar cells are typically fabricated in a glovebox to strictly avoid any water exposure. A dry atmosphere significantly increases equipment and operational costs for industrial processes, so ambient perovskite fabrication will be less expensive and more attractive. In this work it is demonstrated that ambient annealing is comparable to annealing in dry N2. Perovskite films annealed in a standard dry N2 environment are compared with those annealed in ambient environment with 50% relative humidity. Solar cell devices were prepared with a planar structure configuration and annealed at one of three different temperatures (105, 115, or 125 °C) in either N2 or ambient air. For all temperatures, the average efficiencies for the devices annealed in air are higher than those annealed in dry N2. The highest efficiency achieved for air-annealed devices is 12.7%. Thus, good efficiency cells can be fabricated in an ambient environment, which facilitates mass production.
Planar CH 3 NH 3 SnBr 3 perovskite solar cells were fabricated via vapor deposition with a protection against air exposure achieved by a thick MABr overlayer.
The color of the emission of zinc gallate oscillates between ultraviolet and blue by hydrogen ambient reduction and air ambient oxidation heat treatments. The photoluminescence spectra and electron paramagnetic resonance signals show that ultraviolet emission of reduced always accompanies 680 nm emission originating from single oxygen vacancies The increasing difference in binding energy between and in reduced indicates that the configuration of octahedral sites is distorted due to generation and it becomes more ionic which shifts the emission band from 430 to 360 nm. The x-ray diffraction patterns and Raman scattering spectra show that from is formed in both reduction and oxidation processes which suggests the vaporization of Zn ions. We propose a model in which the origin of 360 nm emission is the Ga–O transition at distorted octahedral sites with in whereas 430 nm emission originates from the Ga–O transition of regular octahedral sites without in
We fabricated perovskite solar cells using a triple-layer of n-type doped, intrinsic and p-type doped 2,2′,7,7′-tetrakis(N,N′-di-p-methoxyphenylamine)-9,9′-spirobifluorene (spiro-OMeTAD) (n-i-p) as hole transport layer (HTL) by vacuum evaporation. The doping concentration for n-type doped spiro-OMeTAD was optimized to adjust the highest occupied molecular orbital of spiro-OMeTAD to match the valence band maximum of perovskite for efficient hole extraction while maintaining a high open circuit voltage. Time-dependent solar cell performance measurements revealed significantly improved air stability for perovskite solar cells with the n-i-p structured spiro-OMeTAD HTL showing sustained efficiencies even after 840 h of air exposure.
We investigated Pt-induced nanowires on the Si(110) surface using scanning tunneling microscopy (STM) and angle-resolved photoemission. High resolution STM images show a well-ordered nanowire array of 1.6 nm width and 2.7 nm separation. Angle-resolved photoemission reveals fully occupied one-dimensional (1D) bands with a Rashba-type split dispersion. Local $dI/dV$ spectra further indicate well-confined 1D electron channels on the nanowires, whose density of states characteristics are consistent with the Rashba-type band splitting. The observed energy and momentum splitting of the bands are among the largest ever reported for Rashba systems, suggesting the Pt-Si nanowire as a unique 1D giant Rashba system. This self-assembled nanowire can be exploited for silicon-based spintronics devices as well as the quest for Majorana fermions.
The chemical state of N in N-doped amorphous samples with doping concentrations was investigated by high-resolution x-ray photoelectron spectroscopy (HRXPS) and Ge -edge x-ray absorption spectroscopy (XAS). HRXPS showed negligible change in the Te and Sb core-level spectra. In the Ge core-level spectra, a Ge nitride peak developed at the binding energy of and increased in intensity as the N-doping concentration increased. Generation of was confirmed by the Ge -edge absorption spectra. These results indicate that the N atoms bonded with the Ge atoms to form , rather than bonding with the Te or Sb atoms. It has been suggested that the formation of Ge nitride results in increased resistance and phase-change temperature.