Kemal Sahbudak

Prof. Kemal Sahbudak

orcid

Research Focus & Metrics

Representative Publications

View All Publications
26 August 2020 in SN Applied Sciences
Verified
Journal Article
Closed access
PDF file
ISİbRahim Sönmez
İbRahim Sönmez
KSKemal Sahbudak
Kemal Sahbudak
LKLevent Kartal
Levent Kartal
BABülent Alkan
Bülent Alkan

18 February 2022 in Materials Science
Verified
Journal Article
Closed access
PDF file
KSKemal Sahbudak
Kemal Sahbudak
In this work, the properties of alkali silicate geopolymer type materials and diatomite as additive to fly coal ash was investigated using thermic coal plant’s fly ash in alkaline solution. The reacted products of alumino-silicate geopolymers using fly ash plus diatomite were pseudo-amorphous aluminosilicate gel and calcite and their mechanical and thermal properties were evaluated by the addition of diatomite. The compressive strength of this geopolymer is similar to that of the Portland cement mortar of PC20 (± 20 %) when cured for 28 days while the density and thermal properties are much lower that indicates the insulator properties. Alkaline solution was produced by NaOH in different concentrations to determine the least alkaline solution molarity in the range of 1 M, 3 M and 5 M. The characterization of geopolymers were done by using XRD for phase analysis, SEM for surface and morphological evaluation, compression tests for mechanical properties and transient plane source thermal analysis for thermal insulation properties. The results showed that, 1 M of NaOH alkaline solution and 10wt% diatomite addition can provide enough strength of 18 MPa which is a good candidate for constructional materials. The thermal conductivity coefficient of 10 wt.% diatomite added geopolymer was evaluated as 0.0018 W/m×K which can also be a good candidate for insulator materials to be used in green lateral wall production.

30 June 2023 in Revista de Metalurgia
Verified
Journal Article
Open access
PDF file
ISİbrahim Sönmez
İbrahim Sönmez
KSKemal Sahbudak
Kemal Sahbudak
Turkey’s iron ores may be used to manufacture sponge iron, and the country’s coal resources, which are plentiful despite being of poor quality, can be used as a reducing agent. With such a production, Electric Arc Furnace based on scrap imports, will be an alternative raw material for steel production, and this will create high value due to the usage of domestic resources. In this study, sponge iron production was tried to be optimized by using local sources. For this purpose, the effects of time, temperature and [CFix/FeTotal] weight ratio on the Reduction Degree (%) of the important parameters effective in the production of sponge iron by using Divriği Iron Pellets and Dodurga Lignite as a reductant were studied using a Box-Wilson experimental design. The optimum parameters were determined as 82.59 min, 996.73 °C and 0.49, and the highest Reduction Degree (%) value was calculated as 96.46%. The sponge iron obtained with a 71.91% Reduction Degree contains 97.12% Fe, of which 7.12% is oxidized. It is evident that higher Fe contents may be attained with research carried out in optimum parameters.

29 September 2026 in Buildings
Verified
Journal Article
Open access
PDF file
KSKemal Sahbudak
Kemal Sahbudak
Curing and conditioning are processing variables in geopolymer and alkali-activated materials. Reaction kinetics, phase assemblage, pore development, and later mechanical and durability responses all depend on the environmental history of the binder. Published procedures, however, are often compressed into labels that do not allow the thermal, moisture, and timing paths to be reconstructed. This critical review examines recurring problems in the reporting and interpretation of curing terminology, thermal regimes, moisture and humidity control, pre- and post-curing timing, transfer of curing practices between chemically distinct binder families, and attribution of property changes to curing. Studies on fly ash, slag, metakaolin, red mud, volcanic ash, one-part binders, and phosphate-activated systems show that similar curing labels can conceal important differences in sealing, water availability, heating history, pressure, relative humidity, and specimen state. These differences may alter reaction development and microstructure enough to compromise reproducibility, cross-study comparison, and mechanistic interpretation. Curing is therefore considered here as a processing path that should be reconstructable from the reported procedure. A tiered framework is proposed for minimum, recommended, and comprehensive reporting. Clearer definition of curing paths should improve structure–property interpretation and provide the methodological basis for future comparisons of the resource intensity of thermal and moisture conditioning.

10 September 2024 in Bilimsel Madencilik Dergisi
Verified
Journal Article
Closed access
KSKemal Sahbudak
Kemal Sahbudak
YCYakup Cebeci̇
Yakup Cebeci̇
In the present study, the effect of various The oil agglomeration method is of great importance for high recovery and low cost in capitalizing our energy resources that create environmental problems due to fineness of particle size or our low quality, oxidized coal resources with large reserves. Inorganic pretreatment materials, the ratio of bridging liquid, agglomeration time and mixing speed on the agglomeration recovery in the beneficiation of Zonguldak coal with low ash content (2.23%) through oil agglomeration. In the experiments, kerosene was used as the bridging liquid and NaCl, FeCl2, Fe2(SO4)3, Al2(SO4)3 were used as inorganic pretreatment materials. In the agglomeration experiments in which inorganic pretreatment materials and kerosene were used together, the maximum recovery was determined in the condition where the kerosene concentration was 15%, the mixing speed was 800 rpm and the agglomeration time was 10 min. It was found that, the recovery under suitable conditions was 71.5% in the agglomeration experiments conducted with only kerosene, whereas it was in varying rates between 76.5% and 81.6% in experiments where pretreatment materials and kerosene were used together. Among the inorganic pretreatment materials, when used together with kerosene, the best recovery was obtained with the use of 50 mg/L Fe2(SO4)3. The agglomeration recovery obtained in the experiments conducted with only kerosene under optimum conditions was reached when the agglomeration time was 5 min in the experiments in which the inorganic pretreatment materials and kerosene were used together.

1 March 2017 in Acta Physica Polonica A
Verified
Journal Article
Open access
KSKemal Sahbudak
Kemal Sahbudak