Superconducting joints are crucial for second generation high-temperature superconducting (2G HTS) closed-loop coils that work in the persistent current mode (PCM) operation. Here, we report an efficient approach for superconducting joints of YBa2Cu3O7-σ (YBCO) coated conductors (CCs). The YBCO layer is etched to and from some microchannels, which serve as oxygen diffusion paths during oxygenation annealing (OA), to accelerate the recovery of critical current (Ic) of the joined two YBCO layers. The Ic of the superconducting joint is 118 A at 77 K with an optimized joining temperature and a short OA time (10 h), which is about 82% Ic of the joined YBCO CCs. The persistent field decay of the closed-loop coil shows a joint resistance (Rj) of less than 2.2 × 10−13 Ω at 77 K. Two YBCO films epitaxially grown along the c-axis diffuse into each other at the interface and form a dense joining, enabling superconducting current path. This superconducting joint technique can promote the achievement of the PCM operation in 2G HTS magnet applications, such as magnetic resonance imaging and nuclear magnetic resonance.
23 February 2021 in Superconductor Science and Technology
Although YBa 2 Cu 3 O 72212δ (YBCO) is one of the most promising superconducting materials for power applications, the fabrication of low-cost coated conductors with the high in-field performance remains challenging. Here, we report an efficient mixed-pinning landscape for enhancing the in-field performance of BaTiO 3 (BTO)-doped YBCO films by low-energy (60 keV) proton irradiation. The smaller (2–4 nm), weaker but perhaps denser pinning sites have been successfully introduced by irradiation, which can form a mixed-pinning landscape with pre-doped BTO precipitates (5–15 nm), leading to the increased vortex pinning. In this case, the critical current density ( Jc ) of YBCO films increases significantly, especially at low temperature and high magnetic field, and it increases three times near 6 T at 20 K when the irradiation dose is 1 × 10 15 proton cm −2 . Additionally, the c -axis length ( c -parameter) of YBCO increases with the increase of irradiation dose, which indicates the decreasing oxygen content due to the excessive irradiation, thereby the reduction in critical transition temperature ( Tc ). Employing low irradiation energy is beneficial for protons to stop inside YBCO film and thereby induces higher density defects when applying low doses. This fabrication technique is a practicable post-production solution to improve the in-field performance of nanoparticle-doped YBCO films.
8 January 2021 in IEEE Transactions on Applied Superconductivity
The achievement of low-resistance connection in REB 2 C 3 O 7-z (REBCO, RE = Y, Gd) coated conductors (CCs) has become one of the strategic factors for magnet applications. In this letter, we fabricated low-resistivity (R sj = 4.9 nΩ·cm 2 ) Ag-diffusion joints of REBCO CC by improving the interface connection of the Ag stabilizer. The effective contact area at the interface between two Ag stabilizers can be increased by polishing the surface of the Ag stabilizers, which can reduce joint resistance (R j ). Compared with a traditional diffusion temperature (400 °C), diffusion bonding of the Ag stabilizers at higher temperatures (800 or 850 °C, typical connection temperatures for superconducting joint) can promote interface connection between two Ag stabilizers. The oxygen content in REBCO will be reduced due to diffusion bonding at higher temperatures. Therefore, we etched some microchannels that serve as the fast oxygen diffusion paths on the surface of the Ag stabilizers to help restore the oxygen content, thereby recovering critical current (I c ) and reducing R j . The connection mechanism of the interface between two Ag stabilizers was investigated through the cross-sectional analysis and delamination of the joint part. In addition, the REBCO layer can be completely peeled off and almost retain the original I c by diffusion bonding of the Ag stabilizers at higher temperatures. This fabrication technique is a unique practicable solution to reduce the R j for the CC with thin Ag stabilizers and improve the peeling quality of the REBCO layer for efficiently fabricating the superconducting joint.
2 July 2019 in IEEE Transactions on Applied Superconductivity
The YBa $_2$ Cu $_3$ O $_{7-x}$ (YBCO) coated conductor (CC) is one of the most promising wires because of their high critical current ( $I_c$ ) and low dependency of the $I_c$ on the external magnetic field. For superconducting applications, a large number of joints are required to join relatively short YBCO CCs. In this paper, we study the electromechanical behavior of lap-jointed YBCO CCs fabricated by etching Cu stabilizer at its service temperatures (77 K) under self-field. The effects of etching Cu stabilizer on $I_c$ and joint resistance ( $R_j$ ) were discussed. The Rj fabricated by etching Cu stabilizer was reduced and the $I_c$ values of the joints are consistent with the parent CCs tape by etching the Cu stabilizer. Preferable electrical properties under applying axial tension are achieved and proved by the axial tension tests and finite element simulations. This fabrication technique is a unique practicable solution to reduce joint resistance for YBCO CCs with thicker metal stabilizing layers and improving electromechanical performance in 2G HTS devices.
27 April 2023 in Superconductor Science and Technology
Irradiation can precisely control defects in, and improve the superconducting properties of, REBa2Cu3O7−δ (REBCO, RE: rare earth) coated conductors (CCs). Here we report an effective approach for enhancing the in-field performance of GdBCO CCs. The critical current density (Jc) of GdBCO films was significantly improved through cooperative defects created by co-irradiation with O ions and protons, especially at low temperatures and high magnetic fields. Surprisingly, the in-field Jc of commercial CCs can be nearly doubled. The cooperative irradiation-induced defects are uniformly distributed throughout the GdBCO layer, which promotes the overall performance of the CC. Moreover, the dimensions of these irradiation-induced defects closely match the coherence length of REBCO. This simple and efficient method is a practical post-production solution to improve the in-field performance of commercial REBCO CCs.