This paper proposes a methodology using wavelet packet transform, principal component analysis, and neural networks in order to generate artificial critical aftershock accelerograms which are compatible with the response spectra. This procedure uses the learning abilities of neural networks, principal component analysis as a dimension reduction technique, and decomposing capabilities of wavelet packet transform on consecutive earthquakes. In fact, the proposed methodology consists of two steps and expands the knowledge of the inverse mapping from mainshock response spectrum to aftershock response spectrum and aftershock response spectrum to wavelet packet transform coefficients of the aftershocks. This procedure results in a stochastic ensemble of response spectra of aftershock (first step) and corresponding wavelet packet transform coefficients (second step) which are then used to generate the aftershocks through applying the inverse wavelet packet transform. Finally, in order to demonstrate the effectiveness of the proposed method, three examples are presented in which recorded critical successive ground motions are used to train and test the neural networks.
19 October 2022 in Soil Dynamics and Earthquake Engineering
This paper proposes the ductility demands control of reinforced concrete frames under criticalsuccessive earthquakes using evaluation of behavior factors (R factors). The influence of RC frameperiods, PGA and magnitude of mainshocks and aftershocks is also taken into account by 10 training ideal artificial neural network (ANN) and proposing the empirical equations. Firstly, 2D RC frames are implemented in Opensees and then evaluated under as-recorded critical single and successive scenario. R factors are calculated and compared for single and successive cases. It is found that the sequences of critical records decrease R factors and capacity of RC frames about 18% and 30%, respectively. Despite what is necessitated in the seismic design codes, proposing a constant value as R factor for whole RC structure especially under single scenarios cannot lead to proper design of structures. Hence, the idealized multilayer ANNs employed to generate the empirical charts for evaluation of R factors.
Fragility curves as a powerful tool assess the possible damage to existing structures and estimate the probability of structural damage exceeding a given level of seismic damage for several levels of seismic ground motions. This paper tries to evaluate the seismic vulnerability of steel structures containing relatively new Linked Column Frame (LCF) system—which are not considered by most of the seismic design codes—using the fragility curves under the critical multiple earthquakes. Therefore, 10 LCF steel frames with shear/flexural behavior and length of 2 m have been designed and implemented in OpenSees software. After selecting consecutive critical earthquakes, the fragility curves have been calculated for single and consecutive scenarios. For more comprehensively evaluation of the mentioned structures, the effect of various parameters including the number of stories and behavior of the linked beams has been investigated. Despite what is often assumed by the seismic design codes about singularity of the design earthquake, the results indicate an increase in the probability of collapse under successive shocks compared to a single earthquake. This increase is more obvious in the performance level corresponding to the collapse threshold. So that the collapse prevention of 7-story frame with flexural linked beam exposed to consecutive earthquakes is 17% higher than the single case. Performance comparison of the steel structures with shear/flexure link beams at height showed that the failure exceedance probability has decreased with the increasing the number of stories especially in steel frames with shear link beams. Moreover, structures with shear link beams have higher failure exceedance probability than flexure performance.
The uncertainty and unreliability in the probabilistic seismic demand models (PSDMs) can be addressed in the framework of performance‐based earthquake engineering (PBEE). Some characteristics have been introduced and extensively investigated in the earthquake engineering literature for appropriateness (i.e., optimality) of various intensity measures, such as efficiency, effectiveness, sufficiency, practicality, and hazard computability. The reliability of the intensity measures can also be considered as another important criterion for intensity measure (IM) selection, which has not been investigated extensively. In this paper, a framework has been developed and implemented to investigate the reliability of various intensity measures alongside the number of adopted earthquake records. In this regard, the inverse of the mean coefficient of variation (IMCV), which is detected to be in a direct and linear relationship with the number of earthquake records, is adopted as the main criterion to compare the reliability of ground motion intensity measures. A simple relation has been proposed and calibrated for the studied IMs that provide the required number of earthquake records to satisfy an intended level of reliability. As a case study, a significant number of recorded ground motions at Zagros and non‐Zagros zones (two major seismic regions in Iran) with rock and soil conditions are selected, and the most reliable ground motion intensity measure is introduced at various seismic regions and soil types by exploiting the developed framework and the proposed relationship.